Focal FDP 1.900 Bedienungsanleitung
Lies die bedienungsanleitung für Focal FDP 1.900 (8 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 30 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 15.5 Bewertungen. Hast du eine Frage zu Focal FDP 1.900 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
1
POWER PER CHANNEL:
• 1 x 500 wRMS @ 4ohms
• 1 x 850 wRMS @ 2ohms
• 1 x 500 wRMS @ 1 ohms
• 1 x 1700 wRMS (Two FDP 1.900s Bridged @ 4 ohms only)
INPUT/OUTPUT CONFIGURATIONS
Because this is a one channel amplifier, if both left and right inputs are used, they are mixed to mono, which is useful
for subwoofers.
CROSSOVER CONFIGURATION
The 24 dB per octave crossover can be adjusted so this amplifier can function as:
1. Full range
2. Low Pass for a subwoofer.
3. Band Pass for a subwoofer or midbass of a 3 way speaker.v
4. High Pass for a midbass, midrange or tweeter.
• The amplifier can be used full range with switch in HP position and frequency set to 10 Hz.
HP is always on so it can be used as a subsonic filter.
HP X1 frequency range is 10 Hz to 400 Hz.
HP X10 frequency range is 100 Hz to 4000 Hz.
LP: Adjustment range is 30 Hz to 350 Hz.
Band Pass with switch in LP position and adjusting both HP and LP to desired frequency.
• The remote volume control is always active.
There is a clip distortion light on the remote volume control.
If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.
• Phase is continuously adjustable between 0 degrees and 180 degrees. Adjust by measuring frequency response
at the crossover frequency. Frequency response should be as smooth as possible.
• 40 Hz EQ is adjustable between 0dB and +6dB.
Measure the subwoofer frequency response and adjust EQ to get the smoothest frequency response.
Avoid excess EQ boost because this will make the subwoofer sound “muddy” and cause the amplifier have clip
distortion prematurely.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio
connected to the REM amplifier terminal.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn
on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not
necessary.
FDP 1.900 : ONE CHANNEL AMPLIFIER
Operation / Configuration
Produktspezifikationen
| Marke: | Focal |
| Kategorie: | Empfänger |
| Modell: | FDP 1.900 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Focal FDP 1.900 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger Focal
28 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
20 August 2024
20 August 2024
20 August 2024
20 August 2024
19 August 2024
Bedienungsanleitung Empfänger
- Martin Logan
- Boss
- Avantree
- Comprehensive
- Sommer
- KVH
- Gira
- Quad
- LYYT
- Esoteric
- CAD Audio
- Zehnder
- Revel
- Elysia
- GlobalSat
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
20 Januar 2026
20 Januar 2026
18 Januar 2026
17 Januar 2026
16 Januar 2026
16 Januar 2026
16 Januar 2026
16 Januar 2026
15 Januar 2026