Forte Lighting 7120-01 Bedienungsanleitung
Seiten 1 Beleuchtung
Lies die Bedienungsanleitung für Forte Lighting 7120-01 kostenlos online oder lade das PDF herunter. 14 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
7120-01
Install light bulbs (not included) in accordance with the fixture’s
specifications. Do not exceed the recommended maximum wattage.
Carefully remove all contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old fixture from the
ceiling, including the old crossbar. Remove the crossbar
assembly from the bag. Crossbar (B) contains several
pairs of threaded holes. Find the pair of holes that matches
the spacing of the holes on the junction box and the fixture’s
canopy. Two mounting screws (A) should be attached to
crossbar (B). You may need to tighten nuts (C) to hold these
screws in place. Pull the house wires through the center of
crossbar (B). Place crossbar (B) over the junction box so
that mounting screws (A) are vertical and aligned with
the hole locations on the fixture’s canopy (F). Secure
crossbar (B) to the junction box by tightening the screws.
crossbar
crossbar
There are an 18 inch rod (K), a 12 inch rod (L), and a 6
inch rod (M) included for each fixture. Determine the correct
number of rods needed for proper hanging height. To lengthen
the fixture, add additional rods. If additional rods are needed,
contact the place of purchase to order. To shorten the fixture,
trim the wires to the desired length, leave at least 8 to 10 inches
of wire in addition to the desired length and slide any excess
rods off to discard. Keep in mind that you must use at least the
provided 6 inch rod (M) to hang the fixture. Thread the wires
Push canopy (F) up to the ceiling and tighten the deco nuts (H)
onto the exposed mounting screws (A).
through the rods and pull the wires until taut before
connecting the rods together. Thread bottom rod (M)
onto nipple (N) on the fixture. Thread the nipple of the
top rod onto swivel post (I) of canopy (F). Pull the fixture
wires through the top of the canopy.
SMOOTH
Produktspezifikationen
| Marke: | Forte Lighting |
| Kategorie: | Beleuchtung |
| Modell: | 7120-01 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Forte Lighting 7120-01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beleuchtung Forte Lighting
Forte Lighting 5745-03 Bedienungsanleitung Forte Lighting 5748-04 Bedienungsanleitung Forte Lighting 2404-04 Bedienungsanleitung Forte Lighting 5748-02 Bedienungsanleitung Forte Lighting 2763-01 Bedienungsanleitung Forte Lighting 2760-03 Bedienungsanleitung Forte Lighting 7116-04 Bedienungsanleitung Forte Lighting 5743-02 Bedienungsanleitung
Alle Forte Lighting Beleuchtung Bedienungsanleitungen
Beliebt in Beleuchtung
Forte Lighting 2688-01 Bedienungsanleitung Forte Lighting 7096-06 Bedienungsanleitung Forte Lighting 5535-01 Bedienungsanleitung
Bedienungsanleitung Beleuchtung
Neueste Bedienungsanleitungen für Beleuchtung
Robert Abbey 1791X Bedienungsanleitung IKEA GREJSIMOJS 506.038.66 Bedienungsanleitung IKEA VARMBLIXT 806.135.24 Bedienungsanleitung IKEA BÄVE 903.997.26 Bedienungsanleitung IKEA BACKSTÖRN 505.909.58 Bedienungsanleitung Robert Abbey CI22X Bedienungsanleitung Robert Abbey 317X Bedienungsanleitung Halsey Taylor MFWSF130 Bedienungsanleitung Robert Abbey Z1440 Bedienungsanleitung Robert Abbey S2180 Bedienungsanleitung