Friedland Evo Wirefree D412 Bedienungsanleitung

Lies die bedienungsanleitung für Friedland Evo Wirefree D412 (1 Seiten) kostenlos online; sie gehört zur Kategorie Türklingel. Dieses Handbuch wurde von 31 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 16 Bewertungen. Hast du eine Frage zu Friedland Evo Wirefree D412 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

EvoWirefree 200m*Chime Kit with Light

Instructions –

Please retain theseinstructions for future reference

Pack contents:

Por tableDoorChimewithLight

Bell push&CR2032 Lithium coincellbattery

Adhesive pad,2 x screws (ø3 x m) 2 x wall plugs(ø5 x 25mm)

for mountingthe bellpush

Fig. 6

Fig. 7

7. Programming asecond push

Within5 minutes of pressing the first push, press the second

push

until the chime sounds, then use button B tochange the tune

if required.

If more than 5 minuteshas elapsed sincethe first pushwas

programmed, press andhold both buttons A and B until the chime

sounds, this takesapprox5 seconds.Thechime is now cleared

andcan programmed toone or two door pushes

All EVO andDécorChimesand Bell Pushesuse programming

toensure no interactionfrom other neighbouring systems.

8. SoundSelection

A =Mainpushsound selection

B =Secondpushsound selection

Chime tune options are as follows:

1. Big Ben 2 Note(Default Tune for 1st Push)

2. Mini Bell 4 Note w/ Echo (Default Tune for 2nd Push)

3. Clarinet

4. Altosax

9. FlashingLightandsoundcontrols

The settingsare:

0. Sound only

1. Sound with flashing light

2. Flashing light only

Flashing Light and sound control

To turn the door chime sound off or tostop

the flashingLED lightwhen the bellpush

is pressed,turn knob C

Note: when thechime isbeing programmed

this controlwillnotfunction for5minutes.

Trouble Shooting

Chime not Sounding

Batteries may not be inserted correctly

Check all batteries have been inserted correctly

Chime may be positionedout ofrange of the bell push

Move your chime closer to thebell push

Note:

During the programming cycle thetransmission range may be reduced

The chime will resume optimum range after5 minutes

A metallic object may be blocking the signal from bell push position

Experiment with the location ofthe chime to see if you can move it in a

more suitable place

The battery in thebell push may need replacing

Pressthe bell push. If the confidencelight (D) flashes 5 times after

being pushed, replace the battery

Note: In cold conditions, poor locationor environment, operating at

maximum range itisadvisable toreplace thebattery morefrequently

before the indicatorlightflashes

(i.e every12 - 18 months) to maintainoptimumperformance

Your bell push and chime haven't been programmed

Do the automatic programming of your chime and bell push

The Selectionknobmay have beenset incorrectly

Do position of knob C as described in section 8 above

LED flashing light does not flash

The selectionknob isnot setcorrectly, reset position ofknob C as

describedin section 8 above

A

C

B

0 2

1

C

LED light

Declaration

Novar ED&S herebydeclares thatthis wirefreeproduct is in compliance with

the essentialrequirements and other relevantprovisions ofthe Radio and

TelecommunicationsTerminal Equipment ( R & TTE ) directive,1999/5/EC

GB

Fig. 8

-

+

+

-

+

-

Friedland guarantees this productfor3 years from date ofpurchase.

Proof of purchaseis required,this does notaffect your statutoryrights.

If you require further informationabout our products, call the Friedland helpline

on 01268 563066.

Friedland, The Arnold Centre, Paycocke Road, Basildon, Essex, SS14 3EA,England

www.friedland.co.uk

Fig. 1

Fig. 2

Fig. 3

A

Fig. 4

B

+

You willrequire:

3X LR6 (AA) Alkalinebatteries for theDoor Chime

Onlylong-life Alkaline batteries must be used

Asmall crosshead and flatheadscrewdriver, a ø5mm.masonry drill

Installation

*Pleasenote: Thestatedrange ofthisproduct ismeasuredin open

field conditions.Walls,ceilings and the positioning thebell push or

door chime on or nearmetal structures or reinforcedPVC doors or

doorframeswill reduce thetransmission range.

1. Openthebellpush

Toopen the front cover carefully

insert aflatbladed screw driver,into

the slotandtwistgently (A). When

refitting thefrontcover toensure the

weather proofingismaintained,

always mountthe bellpush inthe

upright position and replace the

coversecurely. Fig.1

2. Tofitorreplacethebattery

Open the frontcover and

insert theCR2032Lithium

coin cellbatteryintothe cover

as showninFig. 2.

3. Mountthebellpush

Ensure the wall surface isclean and dry.

Mount usingeitherthedouble sided

sticky pad on a smooth surface, or the

screws andwall plugsprovided, SeeFig3.

Donot mount the push on or near (< 30cm)

large metalobjects,as itwillblocksignals

from thepush. Next, hookthecover at

thetop, then press down at the bottom to

clip inplace.

4. Testthebellpush

When thebellpushbutton ispressed,

the confidence light(B)

in Fig.4,will

illuminate toreassurethe callerthat

the bellpushis

working.

The lightwillflash5 timeswhen

the batteryneedsreplacing

5. FittheDoorchimebatteries

Remove batterycompartmentcoverandinsert three LR6(AA)

alkaline batteriesasshownin Fig. 8.

The firsttimeachime unitispowered up,thesounds available

are demonstrated.

6. AutomaticProgrammingofbellpushes

First,placethechime close tothedoorpush (within 8m/25ft)

to programthechime andcheck thatitis working.

Pressthe doorpush until the chime responds with a tune.

You can leavethis tune or change the tune byusing buttonA

(see Fig.6,soundselection).

10. ReplacingBatteries

First remove decorative cover

and replace with three LR6 (AA)

alkalinebatteries. (Fig. 8)

When replacingbatteriesthe

chime isstillprogrammed

and canbe usedstraight away.

Produktspezifikationen