Honeywell Performance HBW4PGR1 Bedienungsanleitung

Lies die bedienungsanleitung für Honeywell Performance HBW4PGR1 (3 Seiten) kostenlos online; sie gehört zur Kategorie Überwachungskamera. Dieses Handbuch wurde von 22 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 11.5 Bewertungen. Hast du eine Frage zu Honeywell Performance HBW4PGR1 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

HBW4PGR1 WDR 4MP IR Bullet Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series IP camera.

Follow the instructions in this guide to install and log in to your camera

For instructions on configuring the camera, refer to the user guide on t

CD that came with your camera. If you require additional assistance, ca

the number listed for your region on the back cover.

Cautions and Warnings

WARNINGTo ensure compliance with electrical safety standards, this product is

intended for use with a Listed Power Adapter marked “Limited Power

Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,

TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed

Information Technology Equipment meeting IEEE 802.3af PoE standard.

CAUTION

The Ethernet connection is not intended to be connected to exposed

(outside plant) networks. Do not connect two power sources to the camera

at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

•Read and keep these instructions.

•Confirm the installation surface can support at least three times the weight of the camera.

•Do not aim the camera toward a bright light source for extended periods to prevent damage to the imager.

•Avoid operating the unit under or close to unstable light sources (may cause flickering), or close to fluorescent

lamps or objects reflecting light.

•D o not touch the camera lens.

•Do not drop the camera or subject it to physical shock.

•Do not use a strong or abrasive detergent when cleaning the camera.

•Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the operating

temperature is outside the recommended range of -22°F to 140°F (–3 0°C to 60°C).

•Do not apply power to the camera before completing installation.

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts are missing or damaged,

contact your dealer immediately.

•Camera

•Installation CD

•Quick installation guide

•Allen key (L-wrench)

•

Self- tapping screws (×4)

•Plastic wall anchors (×4)

•Mounting template

CAUTIONInstallation and servicing should be performed only by qualified and experienced technicians to conform

to all local codes and to maintain your warranty.

Preparing the Mounting Surface

1.Apply the mounting template to the mounting surface.

Note Observe the orientation of the cable exit notch on the bracket base. In outdoor the notch installations,

should point downward to prevent water from entering the camera housing.

2.Using the mounting template as a guide, drill pilot holes in the mounting surface, then hammer the supplied four

anchors into the holes.

3.Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.

Mounting and Aiming the Camera

1.If you are using a microSD card with the camera, install it before continuing. To access the microSD card slot,

remove the panel m mon the underside of the camera and insert a icroSD card into theicroSD card slot (refer to

the picture below).

Note Press and hold the reset button abouts 10s when the camera is power on or rebooting to restore the

default settings, including the user name, password, IP address, port NO., ect.

2.Connect one end of the Ethernet cable to the RJ-45 port on the

camera.

3.If the other end of the Ethernet cable is NOT connected to a PoE

switch or NVR, connect the power connector of the camera to a 12

VDC power source.

4.If the camera is installed outdoor, you can adapt the water- proof

accessory for the network cable after the camera is secured on the

installation surfacerefer to the picture (on the right).

5.Attach the camera assembly to the mounting surface using the

supplied screws.

CAUTION

THIS SYMBOL INDICATESTHAT

DANGE OUSRVOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

CA:TUTIONO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NT REMTHE COOVEOVER.

NO USER-SERVICEABLE PAR.TS INSIDE

REFER SERTOQURVICINGALIFIED SEVICE

PERSONNEL.

THIS SYMBOL INDICATESTHAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANYTHIS UNIT.

RISK OF ELECTRIC

SHOCK

DO NT OPENO

Produktspezifikationen