Honeywell Performance HBW8PR2 Bedienungsanleitung

Lies die bedienungsanleitung für Honeywell Performance HBW8PR2 (2 Seiten) kostenlos online; sie gehört zur Kategorie Sicherheitskamera. Dieses Handbuch wurde von 50 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 9 Bewertungen. Hast du eine Frage zu Honeywell Performance HBW8PR2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

HBW8PR2 WDR 8MP IR Bullet Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series IP

camera. Follow the instructions in this guide to install and log

in to your camera. For instructions on configuring the camera,

refer to the user guide on the CD that came with your camera.

If you require additional assistance, call the number listed for

your region on the back cover.

Cautions and Warnings

WARNING

To ensure compliance with electrical safety standards, this product is

intended for use with a Listed Power Adapter marked “Limited Power

Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,

TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed

Information Technology Equipment meeting IEEE 802.3af PoE standard.

CAUTION

The Ethernet connection is not intended to be connected to exposed

(outside plant) networks. Do not connect two power sources to the camera

at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

•Read and keep these instructions.

•Confirm the installation surface can support at least three times the weight of the

camera.

•Do not aim the camera toward a bright light source for extended periods to prevent

damage to the imager.

•Avoid operating the unit under or close to unstable light sources (may cause flickering),

or close to fluorescent lamps or objects reflecting light.

•Do not touch the camera lens.

•Do not drop the camera or subject it to physical shock.

•Do not use a strong or abrasive detergent when cleaning the camera.

•Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments,

where the operating temperature is outside the -recommended range of 22°F to 140°F

(–3 0°C to 60°C).

•Do not apply power to the camera before completing installation.

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts are

missing or damaged, contact your dealer immediately.

•

Camera

•Installation CD

•Quick installation guide

•Allen key (L- wrench)

•

Self-tapping screws (×4)

•Plastic wall anchors (×4)

•Mounting template

CAUTION Installation and servicing should be performed only by qualified and experienced

technicians to conform to all local codes and to maintain your warranty.

Preparing the Mounting Surface

1.Apply the mounting template to the mounting

surface.

Note Observe the orientation of the cable exit notch

on the bracket base. In outdoor installations, the

notch should point downward to prevent water from

entering the camera housing.

2.Using the mounting template as a guide, drill three

pilot holes in the mounting surface, then hammer the

supplied anchors into the holes.

3.Drill a cable entry hole in the mounting surface, then pull the required cables through the

hole.

Mounting and Aiming the

Camera

1.If you are using a microSD card with

the camera, install it before continuing.

Remove the panel on the underside of

CAUTION

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHINTHE UNIT.

CA:TUTIONO REDUCETHE RISK OF ELECTRIC

SHOCK, DO NOT REMOVEOVER.THE C

NO USER-SERVICEABLE PAR.TS INSIDE

REFER SERTO QUVICINGALIFIED SERVICE

PERSONNEL.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANYTHIS UNIT.

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

Figure 1

Produktspezifikationen