Honeywell RTH5160D1003/E Bedienungsanleitung
Honeywell
Thermostat
RTH5160D1003/E
Lies die bedienungsanleitung für Honeywell RTH5160D1003/E (32 Seiten) kostenlos online; sie gehört zur Kategorie Thermostat. Dieses Handbuch wurde von 57 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 29 Bewertungen. Hast du eine Frage zu Honeywell RTH5160D1003/E oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/32
RTH5160 Series
Non-Programmable
Thermostat
Quick Installation Guide
Tools you will need Tools you may need
Wire stripper
Needle-nose pliers Drill and
drill bit (7/32 in)
Included in your box
Screws and
anchors
UWP™
Mounting
System
(UWP)
RTH5160
Thermostat
Quick Install Guide
Small flat head scr
ewdriver
Phillips scr
ewdriver
Pencil
Level
2
Quick Installation Guide
Removing your old thermostat
2 Check that your system is off.
Change the temperature on your
old thermostat to be above room
temperature in heat mode or below
it in cool mode. If you don’t hear the
system turn on within 5 minutes, the
power is off.
Note: If you have a digital
thermostat that has a blank display,
skip this step.
1 Turn power OFF.
To protect yourself and your
equipment, turn off the power at
the breaker box or the switch that
controls your heating/cooling
system.
3 Remove the old thermostat’s
faceplate.
On most thermostats, you can take
off the faceplate by grasping and
gently pulling. Some thermostats
may have screws, buttons, or clasps.
Do not remove any wires from your
thermostat at this time!
75
OFF
OFF
ON
Breaker box
Switch
4 Make sure there are no 120/240V
wires.
Do you have thick black wires with
wire nuts?
Is your thermostat 120V or higher?
If you answered yes to either of
these questions, you have a line
voltage system and the thermostat
will not work.
Wire nut
Thick black wire
OR
3
RTH5160 Series
5 Take a picture of how your wiring
looks right now.
Be sure to include the letters next
to the terminals where the wires
are inserted. This will be a helpful
reference when wiring your new
thermostat.
Tip: If the color of your wires has
faded or if 2 terminals have the
same wire color, use the wire labels
provided in the package to label
each wire.
YR RC
Example of
a jumper
Terminals
6 Record which R-wire(s) you have and write down the color of the wire(s).
Note: Do not include jumpers as a part of your count. The thermostat does
not need jumpers.
Terminal Wire Color
R
Rh
Rc
7 Record the remaining wires and write down the color of the wires.
Check mark the wires that are connected to terminals. Next to the check mark,
write down the color of the wire. Do not include jumpers as a part of your
count.
Check all that apply (Not all will apply):
Terminal Wire Color
Y
G
C
Terminal Wire Color
A or L/A
O/B
W2 or AUX
E
W
K
NOTES:
• C does not power the thermostat display or operations; batteries are
always required.
• If was used on old thermostat you have a wire-saver at the equipment. K
Re-wiring would need to be done so that Y and G are used instead of K.
• The RTH5160 thermostat does not support L/A, S, or U terminals.
• If there are wires in terminals that are not listed, you will need
additional wiring support. Visit yourhome.honeywell.com/support to
find out if the thermostat will work for you.
Produktspezifikationen
| Marke: | Honeywell |
| Kategorie: | Thermostat |
| Modell: | RTH5160D1003/E |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Honeywell RTH5160D1003/E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Thermostat Honeywell
5 Oktober 2024
4 Oktober 2024
30 September 2024
27 September 2024
24 September 2024
15 September 2024
13 September 2024
13 September 2024
12 September 2024
8 September 2024
Bedienungsanleitung Thermostat
- Bryant
- GENERAL Life
- Horstmann
- Devolo
- Nexa
- ACV
- EVE
- Z-Wave
- Sinustec
- Watts
- Emerson
- Lowes
- Carrier
- Oreg
- Itho Daalderop
Neueste Bedienungsanleitung für -Kategorien-
17 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025
12 Juni 2025
12 Juni 2025
12 Juni 2025
8 Juni 2025