Honeywell TH6210U2001/U Bedienungsanleitung

Honeywell Thermostat TH6210U2001/U

Lies die bedienungsanleitung für Honeywell TH6210U2001/U (40 Seiten) kostenlos online; sie gehört zur Kategorie Thermostat. Dieses Handbuch wurde von 51 Personen als hilfreich bewertet und erhielt im Schnitt 3.9 Sterne aus 26 Bewertungen. Hast du eine Frage zu Honeywell TH6210U2001/U oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/40

Package Includes:

• T6 Pro Thermostat

• UWP™ Mounting System

• Honeywell Standard Installation

Adapter (J-box adapter)

• Honeywell Decorative Cover Plate –

Small; size 449/64 in x 449/64 in x

11/32 in (121 mm x 121 mm x 9 mm)

• Screws and anchors

• 2 AA Batteries

• Installation Instructions and User

Guide

T6 Pro

Programmable Thermostat

Installation Instructions

Home

Optional Cover Plate installation

NOTE: If Optional Cover Plate is not

required, see “UWP Mounting System

installation” on next page.

Use the Optional Cover Plate when:

• Mounting the thermostat to an

electrical junction box

• Or when you need to cover paint gap

from old thermostat.

1. Separate the Junction Box Adapter

from the Cover Plate. See Figure 1.

2. Mount the Junction Box Adapter to

the wall or an electrical box using any

of the eight screw holes. Insert and

tighten mounting screws supplied with

Cover Plate Kit. Do not overtighten. See

Figure 2. Make sure the Adapter Plate

is level.

3. Attach the UWP by hanging it on the

top hook of the Junction Box Adapter

and then snapping the bottom of the

UWP in place. See Figure 3.

4. Snap the Cover Plate onto the Junction

Box Adapter. See Figure 4.

Use 2x

supplied

screws #6

5/8”

L/A

O/B

AUX

Power options

Insert R and C wires into

designated terminals for primary

AC power (C terminal is optional

if batteries are installed, but it is

recommended). Remove wires by

depressing the terminal tabs.

Insert AA batteries for primary or backup

power.

UWP Mounting System installation

Use 3x supplied

screws #8 1-1/2”

5. Before starting, turn the power off

at the breaker box or switch. Open

package to find the UWP. See Figure 5.

6. Position the UWP on wall. Level and

mark hole positions. See Figure 6.

Drill holes at marked positions, and

then lightly tap supplied wall anchors

into the wall using a hammer.

‒Drill 7/32” holes for drywall.

7. Pull the door open and insert the wires

through wiring hole of the UWP. See

Figure 7.

8. Place the UWP over the wall anchors.

Insert and tighten mounting screws

supplied with the UWP. Do not

overtighten. Tighten until the UWP

no longer moves. Close the door. See

Figure 8.

Wiring terminal designations

SInput for wired indoor or

outdoor sensors

L/A

- A

Heat Pump fault input (most

common case)

SO/B Changeover valve

YCompressor contactor

(stage 1)

AUX -

Auxiliary heat relay

Heat relay (stage 2)

Y2 Compressor contactor

(stage 2) EEmergency Heat relay

GFan Relay Heat relay (stage 1)W

24VAC common. For 2

transformer systems,

use common wire from

cooling transformer.

KConnect to K on Wire Saver

Module**

Unused

R24VAC power from heating

transformer*

URc 24VAC power from cooling

transformer*

Note: Not all

terminals may be

used, depending

on the system

type that is being

wired. The most

commonly used

terminals are

shaded.

* Terminal can be jumped using Slider Tab. See “Setting Slider Tabs” above.

** The THP9045A1023 Wire Saver Module is used on heat/cool systems when you

only have four wires at the thermostat, and you need a fifth wire for a common wire.

Use the K terminal in place of the Y and G terminals on conventional or heat pump

systems to provide control of the fan and the compressor through a single wire—the

unused wire then becomes your common wire. See THP9045 instructions for more

information.

Set R Slider Tab.

• Use built-in jumper (R Slider Tab)

to differentiate between one or two

transformer systems.

• If there is only one R wire, and it is

connected to the , or R, Rc RH terminal, set

the slider to the up position (1 wire).

• If there is one wire connected to the R

terminal and one wire connected to the Rc

terminal, set the slider to the down position

(2 wires).

NOTE: Slider Tabs for U terminals should be

left in place for T6 Pro models.

Setting Slider Tabs

R/Rc slider tab

UWP Mounting System

Produktspezifikationen

Marke:	Honeywell
Kategorie:	Thermostat
Modell:	TH6210U2001/U
Breite:	104 mm
Tiefe:	28 mm
Produktfarbe:	Weiß
Höhe:	104 mm
Display:	LCD
Programmierbar:	Ja
Typ:	Digital thermostat
Hintergrundbeleuchtung:	Ja
Intelligentes Thermostat:	Nein
Speicherfunktion:	Ja