Hudson Valley Orlando 4816-AGB Bedienungsanleitung

Lies die bedienungsanleitung für Hudson Valley Orlando 4816-AGB (2 Seiten) kostenlos online; sie gehört zur Kategorie Beleuchtung. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 5 Bewertungen. Hast du eine Frage zu Hudson Valley Orlando 4816-AGB oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

FIXTURE INSTALLATION

1.Attach the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is

designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted

to the structure of the building.

2.Open the end link on the CHAIN (8) and attach to the loop on the FIXTURE ASSEMBLY (10). Hang the

FIXTURE ASSEMBLY (10) on the CHAIN (8) at your desired height, and remove excess CHAIN (8).

3.Feed the wire through the CHAIN (8) , SCREW COLLAR (9), CANOPY (7), SCREW COLLAR LOOP (6),

NIPPLE (5), and MOUNTING PLATE (1), and screw the NIPPLE (5) onto the MOUNTING PLATE (1).

4.Open the top link on the CHAIN (8), and Hang the FIXTURE ASSEMBLY (10) to the SCREW COLLAR LOOP

(6).

5.Cut off excess wire, and strip the insulation off the end of the leads.

6.Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bar copper wire) or

the GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT"

WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

7.Connect the fixture lead with the ridge(s) to the neutral (Generally white) wire in the outlet box. Fasten the wires

together with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection

with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO

EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

8.Connect the smooth fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires

same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS

COULD RESULT IN SERIOUS INJURY OR DEATH!

9.Carefully remove the protective covering over on the SHADE (11), lift the SHADE (11) up onto the fixture and

secure using the SOCKET RING (12).

10.Screw the BULB (13) up into the SOCKET of the fixture. The fixture 4810 IS RATED FOR 75 WATT LAMP.

The fixture 4816 IS RATED FOR 100 WATT LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!

11.Push the DIFFUSER (14) into the SHADE (11).

12.Restore power to the outlet at the breaker or fuse box.

ORLANDO

4810, 4816

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS

AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR

TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

Contact us at [email protected]

1

2

3

4

5

6

7

8

9

10

11

12

13

14

ITEMDESCRIPTION

PART NUMBER

1

MOUNTING PLATE

HDW-004810

2

MOUNTING SCREW

HDW-004810

3

GROUND SCREW

HDW-004810

4

WIRE NUTHDW-004810

5

1/4 NIPPLE

HDW-004810

6

SCREW COLLAR LOOP

HDW-004810

7

CANOPYCPY-004810

8

CHAINCHN-004810

9

SCREW COLLAR

HDW-004810

10

FIXTURE ASSEMBLYFAS-004810, 4816

11

SHADESHD-004810, 4816

12

SOCKET RINGRNG-004810

13

BULB

NOT INCLUDED

14

DIFFUSER

DIF-004810, 4816

Produktspezifikationen