Hudson Valley Woodlawn 1728 Bedienungsanleitung

Lies die bedienungsanleitung für Hudson Valley Woodlawn 1728 (2 Seiten) kostenlos online; sie gehört zur Kategorie Beleuchtung. Dieses Handbuch wurde von 14 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 4 Bewertungen. Hast du eine Frage zu Hudson Valley Woodlawn 1728 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

WOODLAWN

1728

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH

HANDS AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE

PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

Contact us at [email protected]

1

12

FIXTURE INSTALLATION

1.Attach the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is

designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to

the structure of the building.

2.Remove the SCREW COLLAR (3) from the COLLAR LOOP (4). Fully thread the NIPPLE (5) onto the COLLAR

LOOP (4). Thread the HEX NUTS (6) onto the NIPPLE (5) along with TOOTH WASHER (7). Then thread the

NIPPLE (5) unto the MOUNTING PLATE (1). Adjust the NIPPLE (5) so that the threads of the COLLAR LOOP (4)

extends 1/4" beyond the CANOPY (8). Secure using HEX NUT (6).

3.Open the end link the of the CHAIN (9) and attach to the FIXTURE ASSEMBLY (10) at the desired height. Slide the

SCREW COLLAR (3) and the CANOPY (8) onto the CHAIN (9). Attach the other end of the CHAIN (9) unto the

COLLAR LOOP (4). Feed the wires through the CHAIN (9) , SCREW COLLAR (3), CANOPY (8), COLLAR LOOP

(4), NIPPLE (5), and MOUNTING PLATE (1).

4.Cut off excess wires, and strip the insulation off the end of the leads.

5.Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bare copper wire) or the

GROUND SCREW (11) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

6.Connect the fixture's SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire

in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (12). Starting 1" below the

fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener.

MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT

CIRCUIT!

7.Connect the fixture's SPT hot (SPT WITH WRITNGS) wire lead to the hot (Generally black) wire in the junction box.

Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO

FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

8.Push the wires back into the junction box. Lift up the CANOPY (8) up to the ceiling, and screw the SCREW

COLLAR (3) onto the COLLAR LOOP (4).

9.Screw the BULB (13) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 60 WATT LAMP. DO NOT

EXCEED THE RECOMMENDED WATTAGE!

10.Restore power to the outlet at the breaker or fuse box.

2

3

4

5

6

7

7

9

10

11

13

ITEMDESCRIPTION

PART NUMBER

1

MOUNTING PLATE

HDW-001718

2

MOUNTING SCREWSCR-001718-M

3

SCREW COLLARSCL-001718

4

COLLAR LOOPLOO-001718

5

NIPPLENIP-001718

6

HEX NUTNUT-001718-H

7

TOOTH WASHERWAS-001718

8

CANOPYCPY-001718

9

CHAINCHN-001718

10

FIXTURE ASSEMBLYFAS-001728

11

GROUND SCREWSCR-001718-G

12

WIRE NUTNUT-001718-W

13

BULB

NOT INCLUDED

Produktspezifikationen