Jabra GN1000 Bedienungsanleitung

Jabra Hi-Fi-Anlage GN1000

Lies die bedienungsanleitung für Jabra GN1000 (31 Seiten) kostenlos online; sie gehört zur Kategorie Hi-Fi-Anlage. Dieses Handbuch wurde von 24 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 12.5 Bewertungen. Hast du eine Frage zu Jabra GN1000 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/31

User guide

Bedienungsanleitung

Guide d’utilisation

Manual del usuario

Guia do utilizador

Istruzioni d’uso

Gebruikershandleiding

Brugsanvisning

Bruksanvisning

Käyttöohje

FIN

1558-369

GN1000_contents.indd 1 11-03-2003, 14:15:09

2 3

About the GN 1000 RHL

When afﬁ xed to your telephone, the GN 1000 RHL mechanically lifts/lowers your tele-

phone’s handset from/to its cradle and remotely communicates with your headset. This

allows you to answer and terminate telephone calls, even while away from your desk.

Assembling and assembly veriﬁ cation

Assembling the product involves locating and preparing the mount-

ing area as well as afﬁ xing the platform. To assemble the product:

1. Take the product from the packaging and remove the quick set up

sleeve from the platform.

2. Locate the handset area of your telephone, as this is where the

product’s platform will be afﬁ xed. In general, you will afﬁ x the

platform on the telephone, as close as possible to the handset’s

receiver.

3. Line up the top edge of the platform as illustrated.

4. Remove the protective ﬁ lm from the adhesive pad on the bottom

of the platform.

Note: The adhesive pad afﬁ xes ﬁ rmly to any surface. Ensure you

have determined the correct location before afﬁ xing the adhesive

pad.

5. Afﬁ x the platform ﬁ rmly to the telephone with the adhesive pads,

as close as possible to the handset’s speaker.

Note: If you are unable to afﬁ x the platform with the adhesive

pads, use the hook and loop fasteners.

English - GN 1000 Remote Handset Lifter user guide

Thank you for choosing the GN 1000 Remote Handset Lifter (RHL) by GN Netcom,

which will provide you with the full beneﬁ ts of GN Netcom cordless products. The

GN 1000 RHL is designed exclusively for use with GN Netcom cordless products.

This user guide will give you information and instructions on assembling, using and

maintaining your GN 1000 RHL and contains the following sections:

• About the GN 1000 RHL

• Assembling and assembly veriﬁ cation

• Features and customisation

• Answering and making telephone calls

• Frequently asked questions

• Operational and safety information

A Connector cord G Ring Sensor

B On-line indicator H Adhesive pads

C Lifter Arm height control I External socket (back)

D Lifter Arm (extendable; 2 positions) J Ring Sensitivity control (back)

E Housing K Ring Sensor on/off button

F Platform L AUX plug

GN 1000 RHL Accessories

M External Ring sensor

N Hook and Loop fasteners

O Adapter kit (see instructions in adapter kit bag)

GN1000_contents.indd 2-3 11-03-2003, 14:15:09

4 5

6. Position the ring sensor on the centre of the telephone speak-

er.

Note: On most telephones the speaker is located underneath

the handset. If you are unsure of the speaker’s location, have

someone call you and note the precise location where the ring-

ing tone comes from.

7. Insert the AUX plug of the connector cord into the AUX socket

at the bottom of the base unit of your cordless headset.

After assembling the product, verify that the product is working cor-

rectly. Complete the following steps:

1. Set your cordless headset to headset mode by pressing the

multifunction/line button on your cordless headset or remote

unit.

If the product is working properly, the lifting arm will lift the

handset out of the telephone’s cradle and you will hear the dial

tone in the headset.

2. If there is no dial tone, adjust the lifting arm height with the

lifting arm height control. The + raises the lifting arm and the

- lowers the lifting arm.

Note: If you still do not hear a dial tone, extend the Lifter Arm

from its factory-set position.

Features and customisation

On-line indicator

The on-line indicator lights when your handset is lifted and you

have a dial tone, and ﬂ ashes continuously when you have deacti-

vated the ring sensor.

Adjusting the Ring Sensor sensitivity

The ring sensor detects the telephone’s ring and is factory pre-set

to most standard telephones. The ring sensor may, however, need

adjustment to recognise a less common telephone ring tone. Raise

and lower the ring sensor’s sensitivity by adjusting the ring sensitiv-

ity control on the back of the unit.

The ring sensor is set correctly when the on-line indicator lights to

indicate an incoming telephone call. If the on-line indicator does not light when the tele-

phone rings, have someone call you and turn the ringer sensitivity control clockwise

until the on-line indicator is lit.

If you have unsuccessfully tried to increase ring sensor sensitivity, mount the external

ring sensor by completing the following:

1. Mount the plug of the external ring sensor to the external socket of the product.

2. Remove the protective ﬁ lm on the external ring sensor and attach it as close as pos-

sible to the telephone’s speaker.

3. Readjust the ring sensor’s sensitivity if the on-line indicator does not light when an

incoming call is received.

Answering and making telephone calls

To answer a telephone call, press the multifunction/line button on

your cordless headset or remote unit. The product will then auto-

matically lift the handset and put the call through.

To terminate a telephone call, press the multifunction/line button on

your cordless headset or remote unit. The product will now lower

the telephone handset and terminate the call.

Note: When using your telephone in speakerphone mode, e.g. for

a conference call, deactivate the ring sensor by pressing the ring

sensor on/off button to the off mode. The on-line indicator will ﬂ ash

when the ring sensor on/off button is in the off mode.

Press the ring sensor’s on/off button to the on setting when you

have completed your speakerphone call.

GN1000_contents.indd 4-5 11-03-2003, 14:15:14

Produktspezifikationen

Marke:	Jabra
Kategorie:	Hi-Fi-Anlage
Modell:	GN1000
Bluetooth:	Ja
Gewicht:	295 g
Produktfarbe:	Schwarz
Verpackungsbreite:	140 mm
Verpackungstiefe:	67 mm
Verpackungshöhe:	190 mm
Paketgewicht:	250 g
Warentarifnummer (HS):	85189000
Ursprungsland:	China
Typ:	Aktive Halterung
Anzahl:	1
Anzahl Produkte pro Versandkarton:	32 Stück(e)
Gewicht Versandkarton:	11910 g
Länge des Versandkartons:	600 mm
Breite des Versandkartons:	399 mm
Höhe des Versandkartons:	316 mm
Markenkompatibilität:	Jabra