JL Audio Stealthbox SB-GM-TRLBLZR/10W3v3/TP Bedienungsanleitung
JL Audio
Nicht kategorisiert
Stealthbox SB-GM-TRLBLZR/10W3v3/TP
Lies die bedienungsanleitung für JL Audio Stealthbox SB-GM-TRLBLZR/10W3v3/TP (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 13 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 7 Bewertungen. Hast du eine Frage zu JL Audio Stealthbox SB-GM-TRLBLZR/10W3v3/TP oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
INSTALLATION
D I F F I C U L T Y :
I N S T A L L A T I O N G U I D E
for the
SB-GM-TRLBLZR/10W3v3
SKU# 94142, & 94144 - 94146
2002-Up Chevrolet Trailblazer / GMC Envoy & 2003-Up Buick Rainier
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With
proper installation, your new vehicle-specific enclosed subwoofer system will deliver
years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your dealer have
the necessary tools and experience to disassemble and reassemble your vehicle properly.
Also, keep in mind that your warranty coverage extends to 2 years if your system is
installed or approved by your authorized JL Audio dealer. If you prefer to perform your
own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital
that the Stealthbox® be properly mounted to the vehicle according to
these instructions. Failure to mount the enclosure properly presents two
problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
S T E P 1
Remove all contents from the cargo area.
Continued on Next Page
S T E P 2
With a 7mm socket, remove the two bolts that are located at
the rear of the passenger's side rear wheel well.
S T E P 3
With a flat bald screw driver, remove the two push/pull tabs
that are located behind the passenger's side rear tire.
SB-GM-TRLBLZR/10W3v3_INSTR_SKU#011184
25
OUT
OF
SUVs with the air compressor only.
S T E P 9
Apply tape to the switch panel to mark your cut line and new
hose nozzle's mounting hole.
Drill a new mounting hole for the hose nozzle as close to the
switch opening as possible.
Cut the bottom of the switch panel just below the new
mounting hole.
SUVs with the air compressor only.
S T E P 1 1
The cut out of the side panel only needs to be as wide as the
switch hold clips that are on the back side of the switch panel.
The cut out of the side panel only needs to be as tall, as from
the bottom of the switch and to the top of the switch panel.
Do not cut the side panel as tall as the tongue that is on
the top and the back side of the switch panel.
Mark the hose nozzle's mounting hole onto the side panel.
SUVs with the air compressor only.
S T E P 1 0
The air compressor switch panel needs to be mounted at the
lower right corner, outside the pocket onto the side panel.
Continued on Next Page
SB-GM-TRLBLZR/10W3v3_INSTR_SKU#011184
S T E P 7
Remove the storage door.
If your SUV does not have the factory air compressor, please
go directly to STEP 14.
SUVs with the air compressor only.
S T E P 6
This compressor is not to be removed out of the wheel well.
Carefully wedge the compressor into the wheel well, so it
stays. Some large zip ties can be used to temporary mount
the compressor out of the way.
Make sure that you do not kink any of the nylon air hose.
SUVs with the air compressor only.
S T E P 5
Look up into the passenger's side rear wheel well. You will
see this metal plate as in the picture.
The air compressor in mounted onto this plate. The plate is
mounted to the chassis with two bolts.
Remove these two bolts.
S T E P 4
With a 10mm box/open end wrench, remove the bolt that is
located in front off the passenger's side rear tire.
With all the mounting hardware removed, remove the plastic
wheel well liner.
If your SUV does not have the factory air compressor, please
go directly to STEP 7.
SUVs with the air compressor only.
S T E P 8
Pop out the panel that hold the air compressor switch and
hose nozzle.
Remove the hose nozzle from panel.
Pop the switch out of the panel, from the back side.
Page 2 • JL Audio, Inc 2016
S T E P 1 7
Back out the socket cup set screws so 1 1/4-inch of threads
are exposed.
Place the Stealthbox® into position by guiding the socket cup
set screws through the holes drilled.
If your SUV does not have the factory air compressor, please
go directly to STEP 20.
SUVs with the air compressor only.
S T E P 1 9
Mount the air compressor back into position.
S T E P 1 8
From under the vehicle, place the supplied fender washers,
flat washers, lock washers and then hex nuts onto each
protruding socket cup set screw and secure. Adjust the
amount of exposed thread on each cup set screw if necessary
keeping in mind that leaving too much exposed tread will
prevent the re-installation of the air compressor and or the
plastic wheel well liner.
Note: For added protection, it is recommended that
you apply a bead of silicone between the vehicle
and the fender washer. After the bolt assembly is
tightly secured, it is also recommended that vehicle
under-coating material is applied to the exposed
Continued on Next Page
SB-GM-TRLBLZR/10W3v3_INSTR_SKU#011184
S T E P 1 5
Note: Before drilling, make sure that you are not
going to be drilling into any gas lines, brake lines,
transmission lines, electrical wiring, transfer case
(4x4 vehicles) or anything else that might cause
a reduction in your weekly pay. Always wear eye
protection when drilling!
With a drill and a 1/2-inch drill bit, drill through the
impression made in the wax square and into the vehicle’s
wheel well.
S T E P 1 4
Thread the supplied pair of socket cup set screws into
the bottom of the Stealthbox®
, leaving 1/2-inch of thread
exposed. Position the Stealthbox ® in the mounting location
and press down on it firmly.
Remove the Stealthbox® carefully, leaving the wax squares
in place. The socket cup set screws will leave impressions in
the wax.
S T E P 1 3
Place one of the supplied wax squares, so the side of the
wax square is flush against the plastic side panel and the
middle of the wax square measures 7-inches from the front
protrusion of the side plastic panel.
Not pictured. Place the second supplied wax square, so the
side of the wax square is flush against the plastic side panel
and the middle of the wax square measures 7-inches from
the rear of the wheel well to the back of the SUV.
S T E P 1 2
Use a hand held rotary tool (Dremel®) with cutting bit, to cut
out the side panel for the compressor switch panel.
Remember the hole for the hose nozzle.
S T E P 1 6
Run speaker wire from the amplifier location to the
Stealthbox® location and check for proper operation of
the woofer.
Page 2 • JL Audio, Inc 2016
7-inches
Produktspezifikationen
| Marke: | JL Audio |
| Kategorie: | Nicht kategorisiert |
| Modell: | Stealthbox SB-GM-TRLBLZR/10W3v3/TP |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JL Audio Stealthbox SB-GM-TRLBLZR/10W3v3/TP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert JL Audio
3 Dezember 2024
3 Dezember 2024
JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Bedienungsanleitung
3 Dezember 2024
JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Bedienungsanleitung
5 Oktober 2024
3 Oktober 2024
30 September 2024
30 September 2024
JL Audio Stealthbox SB-H-RIDGLNE/10W3v3/GA Bedienungsanleitung
22 September 2024
5 September 2024
Bedienungsanleitung Nicht kategorisiert
- Black And Decker
- Audiovox
- Sennheiser
- Socket Mobile
- Jomox
- Naturn Living
- Hecht
- Moen
- Chief
- Hawk-Woods
- Leaptel
- Juniper
- Miomare
- Ford
- Byron
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025