Joy-it SBC-MotoDriver3 Bedienungsanleitung
Joy-it
Nicht kategorisiert
SBC-MotoDriver3
Lies die bedienungsanleitung für Joy-it SBC-MotoDriver3 (17 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 28 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 14.5 Bewertungen. Hast du eine Frage zu Joy-it SBC-MotoDriver3 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/17
Joy IT powered by SIMAC Electronics GmbH Pascalstr. 8 47506 Neukirchen Vluyn www.joy it.net- - - - - -
SBC MOTODRIVER3-
Motor driver board for DC and stepper motors
TABLE OF CONTENTS
1. General information
3. Changing the I2C address
4. Pin assignment
5. Use with Raspberry Pi
4.1 Connection
4.2 Installation
4.3 Use of stepper motors
5. Use with Raspberry Pi Pico
5.1 Connection
5.2 Installation
5.3 Code example
5.4 Use of stepper motors
6. Use with ARD- -ONE C (Arduino compatible)
6.1 Connection
6.2 Installation
6.3 Code example
6.4 Use of stepper motors
7. Use with micro:bit
7.1 Connection
7.2 Installation
7.3 Code example
7.4 Use of stepper motors
7.5 Pairing the micro:bit
8. Additional information
9. Support
1. GENERAL INFORMATION
Dear Customer,
thank you for choosing our product. In the following, we will show you
what you should pay attention to during commissioning and use.
Should you encounter any unexpected problems during use, please feel
free to contact us.
With the MotoDriver3 you have the possibility to control and power up to
four DC motors or two stepper motors. The connected motors are
controlled via the PCA9634 chip, which provides an I2C interface.
This motor driver board can be configured to 128 possible I2C addresses.
These can be chosen freely, but in the further course the default address
0x15 is used.
In the following figure you can see which resistors can be changed to
change the I2C address of the motor driver board. You can re solder these -
resistors from A1 up to A7 between GND and VDD to get dierent I2C
addresses.
Here the positions of the seven resistors can be translated to a 7 bit -
binary value. Here we take the standard address of the motor driver
board
0x15
which can be translated to
001 0101b
:
A1 = 1 | A2 = 0 | A3 = 1 | A4 = 0 | A5 = 1 | A6 = 0 | A7 = 0
It should be noted that one should never change the I2C address
during operation as this can lead to unpredictable problems.
2. CHANGING THE I2C ADDRESS
Produktspezifikationen
| Marke: | Joy-it |
| Kategorie: | Nicht kategorisiert |
| Modell: | SBC-MotoDriver3 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Joy-it SBC-MotoDriver3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Joy-it
6 September 2024
5 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
3 September 2024
3 September 2024
3 September 2024
Bedienungsanleitung Nicht kategorisiert
- Kwikset
- IODD
- Chauvet
- Rocktrail
- Black And Decker
- SRS
- Movo
- Muller
- Wortmann AG
- Taurus
- Deltex
- Silent Angel
- Trisa
- Sencys
- Black Line
Neueste Bedienungsanleitung für -Kategorien-
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025