Lectrosonics LMb/X Bedienungsanleitung

Lectrosonics Nicht kategorisiert LMb/X

Lies die bedienungsanleitung für Lectrosonics LMb/X (24 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Lectrosonics LMb/X oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/24

LMb

Digital Hybrid Wireless

UHF Belt Pack Transmitter

Featuring

Digital Hybrid

Wireless

INSTRUCTION MANUAL

Rio Rancho, NM, USA

www.lectrosonics.com

Fill in for your records:

Serial Number:

Purchase Date:

Quick Start Steps

1) Install good batteries and turn power on (see

pages 5 and 6).

2) Set compatibility mode to match the receiver (see

page 9).

3) Connect signal source and adjust input gain for

optimum modulation level (see page 9).

4) Set StepSize and frequency to match receiver

(see page 10). Also see receiver manual for scan-

ning procedure.

5) Turn on the receiver and verify RF and audio

signals are present (see receiver manual).

LMb, LMb/E01, LMb/E06, LMb/X

WARNING: Moisture, including talent’s sweat,

will damage the transmitter. Wrap the LMb in

a plastic baggie or other protection to avoid

damage or see LMCVR.

LMb, LMb/E01, LMb/E06, Lmb/X

LECTROSONICS, INC.

Table of Contents

Quick Start Steps ................................................................................................................................................................................. 1

Introduction ............................................................................................................................................................................................. 3

About Digital Hybrid Wireless .............................................................................................................................................................3

Frequency Agility .................................................................................................................................................................................3

Servo Bias Input and Wiring ................................................................................................................................................................ 3

DSP-controlled Input Limiter ............................................................................................................................................................... 3

LMb Block Diagram .............................................................................................................................................................................4

No Pre-Emphasis/De-Emphasis .........................................................................................................................................................4

Pilot Tone Squelch ...............................................................................................................................................................................4

Battery Installation .................................................................................................................................................................................5

Belt Clips .................................................................................................................................................................................................5

Operating Instructions ...........................................................................................................................................................................6

Battery Status LED Indicators ............................................................................................................................................................. 6

Powering On in Operating Mode .........................................................................................................................................................6

Powering On in Standby Mode ...........................................................................................................................................................7

Powering Off ........................................................................................................................................................................................7

Navigating Menus ................................................................................................................................................................................7

Locking/Unlocking Changes to Settings ............................................................................................................................................7

Power Menu Options ...........................................................................................................................................................................7

Selecting Programmable Switch Functions .......................................................................................................................................8

Main Window Indicators ...................................................................................................................................................................... 8

Selecting the Compatibility (Compat) Mode ......................................................................................................................................9

Connecting the Signal Source .............................................................................................................................................................9

Adjusting the Input Gain ...................................................................................................................................................................... 9

Selecting Step Size .............................................................................................................................................................................. 9

Selecting Frequency ..........................................................................................................................................................................10

Selecting Frequency Using Two Buttons .......................................................................................................................................... 10

Helpful Features on Receivers ..........................................................................................................................................................10

About Overlapping Frequency Bands ...............................................................................................................................................10

Selecting Audio Polarity (Phase) .......................................................................................................................................................11

Adjusting LCD Backlight ...................................................................................................................................................................11

RF ON/OFF on the Menu ...................................................................................................................................................................11

Selecting Battery Type .......................................................................................................................................................................11

Restoring Default Settings ................................................................................................................................................................11

IR (infrared) Sync ...............................................................................................................................................................................11

5-Pin Input Jack Wiring ........................................................................................................................................................................12

Microphone Cable Terminationfor Non-Lectrosonics Microphones ...............................................................................................13

Input Jack Wiring for Dierent Sources .............................................................................................................................................14

Microphone RF Bypassing ................................................................................................................................................................15

Line Level Signals ..............................................................................................................................................................................15

Wiring Diagram for MI39A Instrument Cable .................................................................................................................................... 15

Supplied and Optional Accessories ....................................................................................................................................................16

Troubleshooting .................................................................................................................................................................................... 17

Specications and Features ................................................................................................................................................................ 18

Service and Repair ...............................................................................................................................................................................19

Returning Units for Repair .................................................................................................................................................................19

Consumer Alert for US Users - FCC Order DA 10-92

Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this

microphone system without a license is subject to certain restrictions: the system may not cause harmful

interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from

interference received from any other device. Purchasers should also be aware that the FCC is currently evaluat

ing use of wireless microphone systems, and these rules are subject to change. For more information, call the

FCC at 1-888- CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC’s wireless microphone website at www.fcc.

gov/cgb/wirelessmicrophones. To operate wireless microphone systems at power greater than 50mW, you

must qualify as a Part 74 user and be licensed. If you qualify and wish to apply for a license go to: http://www.

fcc.gov/Forms/Form601/601.html