Metra XSVI-9006-NAV Bedienungsanleitung
Metra
Nicht kategorisiert
XSVI-9006-NAV
Lies die bedienungsanleitung für Metra XSVI-9006-NAV (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 14 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 7.5 Bewertungen. Hast du eine Frage zu Metra XSVI-9006-NAV oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
XSVI-9006-NAV
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 3/11/19 INSTXSVI-9006-NAV
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties • Small flat-blade screwdriver
TABLE OF CONTENTS
Connections ............................................................2
Installation ............................................................. 3
Programming .........................................................3
Volkswagen Data Interface 2015-up
APPLICATIONS
• Provides accessory power
(12-volt 10-amp)
• Retains R.A.P. (retained
accessory power)
• Provides NAV outputs (parking
brake, reverse, speed sense)
• For use in non-amplified
systems, or when replacing an
amplified system
• 48-inch leads for remote tuner
location
• Pre-wired ASWC-1 harness
(ASWC-1 sold separately)
• Retains the factory backup
camera
• Retains balance and fade
• Micro-B USB updatable
Volkswagen
Beetle 2016-2019
Golf Series 2015-up
Jetta 2016-2018
Jetta GLI 2016-2018
Passat 2016-up
Tiguan 2016-2017
• XSVI-9006-NAV interface
• XSVI-9006-NAV harness
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date
vehicle specific applications
2
CONNECTIONS
From the XSVI-9006-NAV harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• Connect the wire to the accessory wire.Red
• If the aftermarket radio has an illumination wire, connect the Orange wire to it.
• Tape off and disregard the wire, it will not be used in this application.Blue/White
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
• Connect the wire to the radio’s left rear positive speaker output.Green
• Connect the wire to the radio’s left rear negative speaker output.Green/Black
• Connect the wire to the radio’s right rear positive speaker output.Purple
• Connect the wire to the radio’s right rear negative speaker output.Purple/Black
The following (3) wires are for aftermarket multimedia/navigation radios that provide these
wires (if not required, tape them off and disregard them).
• Connect the wire to the parking brake wire.Light Green
• Connect the wire to the VSS or speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
•
If retaining the factory backup camera, connect the Yellow RCA jack to the backup camera input
.
12-pin ASWC-1 harness & 3.5mm jack:
The 12-pin ASWC-1 harness & 3.5mm jack are to be used with an ASWC-1 (sold separately) to
retain steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness
and 3.5mm jack. If it is to be used, please refer to the ASWC-1 instructions for radio connections
and programming. Disregard the harness that comes with the ASWC-1.
DIN Connector:
The DIN plug is to be connected to the optional AX-LCD screen (sold separately) to retain the
personalization menu that is lost when removing the factory radio.
3
REV. 3/11/2019 INSTXSVI-9006-NAV
With the key in the off position:
Connect the 1. XSVI-9006 harness into the interface, and then to the wiring harness in the
vehicle.
The harness will connect to the harness removed from the disc drive located in the Note:
glove box for remote tuner applications.
If an (sold separately) will be used, do not connect it until the interface is 2. ASWC-1
programmed and fully functional.
Attention! If the interface ever loses power, the following steps will need to be performed again.
Please ensure that the owner of the vehicle knows this.
1.
Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on
.
If the radio doesn’t not come on within 60 seconds, turn the key to the off position, Note:
disconnect the interface, check all connections, reconnect the interface, and then try again.
2. Turn the key (or push-to-start button) to the off position, then to the accessory position.
Test all functions of the installation for proper operation, before reassembling the dash.
INSTALLATION PROGRAMMING
Produktspezifikationen
| Marke: | Metra |
| Kategorie: | Nicht kategorisiert |
| Modell: | XSVI-9006-NAV |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Metra XSVI-9006-NAV benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Metra
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Debel
- Bowflex
- Fibaro
- Simrad
- HealthPostures
- Fritel
- AOC
- Grosfillex
- Byron
- Creamsource
- Flavel
- Orbsmart
- Avital
- MediaMatrix
- Reich
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025