Mikrotik SXT 2 Bedienungsanleitung

Mikrotik Nicht kategorisiert SXT 2

Lies die bedienungsanleitung für Mikrotik SXT 2 (5 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 8 Personen als hilfreich bewertet und erhielt im Schnitt 3.7 Sterne aus 4.5 Bewertungen. Hast du eine Frage zu Mikrotik SXT 2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/5

SXT 2

SXT is an outdoor wireless router that can be used as a CPE in a PtM setup, or for point-to-point links. Please ensure the device is correctly mounted, with

the cable pointing straight down.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Assembly and mounting

With the clip pointed forward, slide the mounting bracket into the rail on the bottom of the case, until the clip clicks into place. The SXT comes bundled with

a hose clamp, guide the clamp through the opening in the bracket and around the pole where it will be mounted. Tighten the hose clamp screw when

alignment is complete. Two screw holes are provided as additional security against accidental bracket movement.

The SXT device has a sliding door, behind which the Ethernet port and the reset jumpers are located. This door can be also secured shut with a screw in

the provided screw hole.

Connecting

Open the ethernet door to connect an ethernet cable to the ethernet port, connect the other end of the ethernet cable to the included PoE injector.

Plug the PoE injector into your network switch or computer.

Plug the included power supply into the PoE injector to start up the device.

Set LAN computer IP configuration to (DHCP).

automatic

The default IP address of the unit is 192.168.88.1, open this address in your web browser to start the configuration. The username is admin and

there is no password . (or, for some models, check user and wireless passwords on the sticker)

Please select your country in the screen that loads, to ensure your device meets local regulations. Set a wireless password, a management

password, and upgrade the device to the latest software with the "check for updates" button.

The device is preconfigured as a wireless client (CPE), and all you need to do is select the AP to connect to and set a device password. You can do this in

the quickSET tab that is loaded by default. In case an IP connection is not available, Winbox can be used to connect to the MAC address of the device.

In case you wish to boot the device from the network, for example, to use MikroTik Netinstall, hold the RESET button of the device when starting it, until

the LED light turns off, then the device will start to look for Netinstall servers.

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and

stability. More information about using RouterOS and connecting to this device

in our documentation: *+https://mt.lv/help+*

Powering

The device only accepts 8-32 V power from Passive PoE injectors (one power supply and PoE injector are included).

Extension Slots and Ports

Produktspezifikationen

Marke:	Mikrotik
Kategorie:	Nicht kategorisiert
Modell:	SXT 2
Breite:	140 mm
Tiefe:	140 mm
AC-Netzadapter:	Ja
Produktfarbe:	Weiß
Höhe:	56 mm
AC Eingangsspannung:	8 - 30 V
Gleichstrom-Anschluss (DC):	Ja
Betriebstemperatur:	-40 - 70 °C
Netzstandard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Schnellstartübersicht:	Ja
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Warentarifnummer (HS):	85176990
Stromverbrauch (max.):	11 W
Maximale Datenübertragungsrate:	300 Mbit/s
Ethernet LAN Datentransferraten:	10,100,1000 Mbit/s
2,4 GHz:	Ja
Antenne Zunahmeniveau (max):	10 dBi
Eingebaut:	Nein
LED-Anzeigen:	Network, Power, WLAN
Montageset:	Ja
Speicherkapazität:	64 MB
Eingebauter Prozessor:	Ja
Antennenfunktionen:	Integrierte Antenne
Flash-Speicher:	16 MB