Philips Series 1000 NT1620 Bedienungsanleitung

Philips Bartschneider Series 1000 NT1620

Lies die bedienungsanleitung für Philips Series 1000 NT1620 (6 Seiten) kostenlos online; sie gehört zur Kategorie Bartschneider. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Philips Series 1000 NT1620 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Seite 1/6
NT1620
© 2019 Koninklijke Philips N.V.
All rights reserved
Tous droits réservés
4222.002.9269.1 (7/11/2019)
2
3
AA
4
5
7
10
11
12
13
>75 % recycled paper
>75 % papier recyclé
English
IMPORTANT SAFETY INSTRUCTIONS
When using an electric product, basic precautions
should always be followed, including the following:
Read all instructions before using this product.
WARNING
To reduce the risk of burns, fire, electric shock, or
injury to persons:
- Use product only in dry condition. Do not use
while bathing or in a shower.
- Close supervision is required when this product
is used by, on, or near children, or persons with
limited physical, sensory, or mental capabilities
or invalids.
- Use this product only for its intended
household use as described in this manual. Do
not use attachments not recommended by
Philips North America LLC.
- Never drop or insert any object into any
opening.
- Never operate this product if it is not working
properly, after it has been dropped or
damaged, or after the product has been
dropped into water. For assistance call
1-800-243-3050.
- Do not use this product outdoors or operate
where aerosol (spray) products are being used
or where oxygen is being administered.
- Never put the product in direct sunlight or store
at a temperature above 140 °F (60 °C).
- Always check cutters, cutting unit and guards
before using the product. Do not use the
product if cutters, cutting unit or guards are
damaged, as injury may occur.
- Only use the accessories supplied with the
product.
- If product will not be used on a regular basis,
remove the battery to prevent possible damage
due to chemical leakage. If battery does leak,
remove it carefully. Do not allow bare skin to
touch leaking fluid.
- The batteries used in this product may present
a fire or chemical burn hazard if mistreated. Do
not disassemble, heat above 100 °C (212 °F) or
incinerate.
SAVE THESE INSTRUCTIONS
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Cutting element
2 Rotary trimmer attachment
3 'Unlocked' indication
4 'Locked' indication
5 Locking indicator
6 Handle
7 Setting indicator
8 'On' indication
9 'Off' indication
10 'Open' indication
11 Battery compartment cover
12 Cleaning brush
Preparing for use
Inserting the battery
Note: Make sure your hands and product are dry
when you insert the battery.
1 To remove the battery compartment cover, turn
it clockwise until the setting indicator points to
the 'unlocked' indication (^) (Fig. 2).
2 Pull the battery compartment cover off the
handle (Fig. 3).
3 Put the battery in the battery compartment (Fig.
4).
Make sure the + and - poles of the battery
point in the right direction.
Note: The product operates on one replaceable
AA 1.5-volt battery (not included).
4 Slide the battery compartment cover back onto
the handle (Fig. 5).
5 Turn the battery compartment cover
counterclockwise until the setting indicator
points to the 'locked' indication (0) (Fig. 6).
3 4 5
1
2
6
7
8
11
9
10
12
1
Using the product
Switching the product on and off
1 To switch on the product, turn the battery
compartment cover counterclockwise until the
setting indicator is aligned with the 'on'
indication (I) (Fig. 7).
2 To switch off the product, turn the battery
compartment cover clockwise until the setting
indicator is aligned with the 'off' indication (0).
Detaching and attaching the rotary
trimmer
Note: Switch off the product before detaching or
attaching the rotary trimmer.
1 To detach the rotary trimmer from the handle,
firmly grasp the attachment below the cutting
element and turn it clockwise until the setting
indicator points to the 'unlocked' indication (^).
2 Lift the attachment off of the handle. (Fig. 8)
1 To attach the rotary trimmer to the handle,
place the attachment on the handle with the
setting indicator pointing to the 'unlocked'
indication (^).
2 Firmly grap the attachment below the cutting
element and turn it clockwise until the setting
indicator points to the 'locked' indication (0).
Tip: If the rotary trimmer becomes clogged, detach
the attachment and rinse it thoroughly with warm
water before you reattach it.
Trimming ear hair
Make sure your outer ear channels are clean and
free from wax.
1 Switch on the product.
2 Slowly move the rotary trimmer along the rim of
the ear to remove hairs that stick out beyond
the rim.
Do not insert the rotary trimmer more than
5 mm (13/64 in) into your ear channel, as this
could damage the eardrum.
3 Carefully insert the rotary trimmer into the outer
ear channel. (Fig. 9)
4 Slowly turn the rotary trimmer around to
remove all unwanted hairs from your outer ear
channel.
5 Clean thoroughly after each use (see 'Cleaning').
Trimming nose hair
Make sure both the product and nasal passages
are clean before trimming. Dried nasal mucus can
block the cutting element, preventing the product
from turning on.
1 Switch on the product.
2 Carefully insert the rotary trimmer into one of
your nostrils.
Do not insert the rotary trimmer more than
5 mm (13/64 in) into your nostrils.
3 Slowly move the rotary trimmer around inside
each nostril (Fig. 10), making sure that you hold
the side of the trimmer firmly against the skin.
This will reduce the tickling effect that can
occur.
4 Clean thoroughly after each use (see 'Cleaning').
Cleaning
Do not immerse the motor unit in water or any
other liquid, or rinse it under the tap.
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as gasoline or acetone
to clean the product or any attachments or
accessories.
Do not tap on the cutting elements.
Do not use any sharp objects to clean the cutting
element.
Clean the rotary trimmer immediately after use and
when a lot of hair or dirt has accumulated on the
cutting element.
1 Use the cleaning brush to remove any excess
hair from the cutting element. (Fig. 11)
2 Switch on the product and rinse the nose hair
trimmer attachment with hot water (Fig. 12).
3 Turn off the product and remove the rotary
trimmer attachment.
4 Turn the attachment upside down, and rinse it
with lukewarm water (Fig. 13).
5 Carefully shake off excess water and let all parts
air dry.
Storage
Store the product in a safe, dry location. Make sure
that the product and accessories are completely
dry before you store them.
Disposal
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused. For recycling information,
please contact your local waste management
facilities or visit .www.recycle.philips.com
This product contains batteries:
- Dispose of batteries properly. Do not incinerate.
Batteries may explode if overheated.
- Do not wrap in metal or aluminum foil. Tape the
waste battery terminals before discarding.
- It is suggested that you contact your local town
or city to determine proper battery redemption
site(s) in your area.
Removing the disposable battery
To remove the disposable battery, see chapter
'Preparing for use'.
Warranty and support
If you need information or support, please
www.philips.com/support or call toll free:
1-866-800-9311.


Produktspezifikationen

Marke: Philips
Kategorie: Bartschneider
Modell: Series 1000 NT1620

Brauchst du Hilfe?

Wenn Sie Hilfe mit Philips Series 1000 NT1620 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten