Prestige APSRS Bedienungsanleitung
Prestige
Nicht kategorisiert
APSRS
Lies die bedienungsanleitung für Prestige APSRS (30 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Prestige APSRS oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/30
Installaon and Reference Guide
2019 Voxx Electronics Corporaon. All rights reserved. APSRS_RevC_9/19
2 Wire Harness Colors and Funcons
2 Power Connector
3 Nocaon Connector
4 Input / Output Connector
7 External Components
7 RF Antenna Kit
7 Data Bus Interface (DBI)
7 Telemacs
8 Setup Opons
8 Remote Programming
9 Keyless Control
12 Remote Start Control
16 Negave Output Control (NOC)
18 AUX Output Control
19 System Operaon
19 Manual Transmission Mode
20 Remote Operaon
APSRS
Vehicle Keyless / Remote Start System
21 Setup Opons
21 Programming Mode Entry / Exit
22 Feature Bank Opons
23 Programming & Diagnoscs
23 Data Port Protocol Selecon
23 Tach Funcon
23 Dome Light Delay
24 2 / 4 Hour Timer
24 Turbo Timer
24 Silent Arm and Disarm
25 User Selectable LED
25 Troubleshoong Trigger Zones
25 Troubleshoong Remote Start
26 Wiring Diagrams
26 Door Lock Connecons
29 Starter Kill Relay
30 Full System Connecons
Thank you for trusng Presge products! If you are a consumer, please note:
Professional installaon is strongly recommended.
This manual assumes the installer has adequate knowledge of the following experse. Therefore, it does not
cover these topics in detail:
• 12-volt electronics
• Tesng and verifying circuits
• Making safe and lasng wiring connecons
• Factory ignion, power, lighng, data bus and sensing systems
• Factory systems and components to avoid
• Safe wire roung, circuit protecon and product placement
• Access to vehicle-specic technical informaon
In addion, this manual assumes the installer has the proper tools, skill and facilies to perform a professional installaon.
Performing an improper installaon could result in damage to the vehicle or its components, improper system funcon,
unsafe vehicle operaon or physical injury. Such instances would not be covered by the vehicle manufacturer's warranty,
nor by Voxx Electronics, Inc.
Detailed Descripons Quick Reference
APSRS_RevC_9/19
2
Detailed Descripons: Wire Harness Colors and Funcons
Power Connector (8-pin High-Current Connector) See page 28 for the full system diagram.
These wires are listed in order of their placement in the harness connector.
3. YELLOW – Starter Output for Remote Start (+)
The YELLOW wire supplies 12-Volt (+) to the vehicle’s starter wire when remote start is enabled, and turns o once the
vehicle is started.
Vericaon: This starter wire registers 12-Volt (+) during engine crank.
Note: If installing a starter kill relay in addion to remote start, connect the YELLOW wire to the MOTOR SIDE of the cut
starter wire. Refer to Start Kill diagram on page 29.
5. RED – 12-Volt Input (+)
The RED wire connects to the vehicle’s primary 12-Volt (+) wire to power the system.
Vericaon: The power wire registers 12-Volt (+) at all mes.
Note: Before making this connecon, remove all module fuses unl the system is completely connected.
4. GREEN – Ignion 2 Output (+)
At its default seng, the GREEN wire supplies 12-Volt (+) to the vehicle’s secondary ignion wire during remote start.
Vericaon: If present, the secondary ignion wire registers 12-Volt (+) when the vehicle is in ignion mode AND during
engine crank.
Note: This wire can be programmed to perform a dierent funcon by changing its opons. Refer to Bank 3, Feature 7
on page 12.
6. RED/WHITE – 12-Volt Input (+)
The RED/WHITE wire connects to the vehicle’s secondary 12-Volt (+) wire to power the remote start funcon.
Vericaon: The power wire registers 12-Volt (+) at all mes.
Note: Before making this connecon, remove all module fuses unl the system is completely connected.
1 3 5 7
2 4 6 8
1. RED/BLACK – Ignion 3, Flex Relay Input (Internal Relay Pin 87)
The RED/BLACK wire is used to supply the Pin 2 - PINK Flex Relay Output. This wire can be connected to 12-Volt (+) or
Ground (-). Please check vehicle requirements for correct polarity.
Note: Before making this connecon, remove all module fuses unl the system is completely connected.
2. PINK – Ignion 3 Flex Relay Output (Internal Relay Pin 30)
At its default seng, the PINK wire supplies 12-Volt (+) or Ground (-) to the vehicle’s secondary ignion wire during
remote start. The polarity of this output is provided by the Pin 1, RED/BLACK Input.
Vericaon: If present, the secondary ignion wire registers 12-Volt (+) or Ground (-) when the vehicle is in ignion mode
AND during engine crank.
Note: This wire can be programmed to perform a dierent funcon by changing its opons. Refer to Bank 3, Feature 8
on page 12.
Produktspezifikationen
| Marke: | Prestige |
| Kategorie: | Nicht kategorisiert |
| Modell: | APSRS |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Prestige APSRS benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Prestige
1 August 2025
1 August 2025
1 August 2025
Bedienungsanleitung Nicht kategorisiert
- ECS
- Helix
- The Grainfather
- Triton
- Fitbit
- Westinghouse
- Philco
- Stirling
- Amplicom
- Gerber
- Speco Technologies
- Nubert
- CENTURY
- Acard
- Kopul
Neueste Bedienungsanleitung für -Kategorien-
5 August 2025
5 August 2025
5 August 2025
5 August 2025
5 August 2025
5 August 2025
5 August 2025
5 August 2025
5 August 2025