Pro1 R250W Bedienungsanleitung

Lies die bedienungsanleitung für Pro1 R250W (2 Seiten) kostenlos online; sie gehört zur Kategorie Thermostat. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.1 Sterne aus 9 Bewertungen. Hast du eine Frage zu Pro1 R250W oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

R250W

Pro1 Technologies

P.O. Box 3377

Springeld, MO 65804

Toll Free : 888-776-1427

Web: www.pro1iaq.com

Hours of Operation: M-F 9AM - 6PM Eastern

Table of ContentsPage

Una version en espanol de este

manual se puede descargar en la

pagina web de la compania.

Rev. 2403

Installing Batteries

21

Establishing Communication

3

4

To install 2 AA batteries remove the cover of the front housing and

insert batteries as show below.

Installing Batteries

Do not operate the cooling

system if the outdoor

temperature is below 50˚F

(10˚ C) to prevent possible

compressor damage.

Caution: Equipment

Damage Hazard

U.S. Registered Trademark. Patents pending

Copyright 2024 All Rights Reserved.

The R250W requires the PROsync™ Wireless System

T755WHO thermostat.

NOTE About Low Batteries:

When the outdoor sensor batteries need to be changed

the Main Thermostat will ash OUTDOOR LO BAT as seen

above. When OUTDOOR LO BAT appears, the user has

~3 months to change the batteries.

Connecting to the Main Thermostat

The Outdoor Sensor must be paired to

a PROsync Equipment Module.

(sold separately)

To check the connection of the outdoor remote sensor to the equipment

module at the installation site, press the button on the outdoor sensor

(located under the front cover) and wait 15 seconds. The LED will blink

white while the outdoor sensor is checking the connection and then show

the following status indicators: BLUE - Good Connection - YELLOW -

Weak Connection - RED - No Connection / out of range.

Specications

Operating Temperature ...................... -40˚F to 140˚F (-40˚C to 60˚ C)

Operating humidity............................... 90% non-condensing maximum

Dimensions of sensor .......................... 3.875”W x 3.875”H x 1.125”D

Checking outdoor remote sensor

temperature:

After the outdoor remote sensor is

paired, on the indoor remote sensor

press the light button(A) and WAIT 30

seconds.

The antenna icon(B) will ash 3 times,

and the outdoor temperature(C) will

appear at the top of the LCD screen.

FAN ON

LEAVE

Set At

COOL ON

Mounting the Outdoor Sensor

On the Equipment Module:

1. Press the PAIR button below the LED.

The equipment module will begin

double blinking pink for 2 minutes

while it waits for a remote to join.

2. Press the button on the inside of the

outdoor remote sensor (A). The LED on

the outdoor remote sensor will begin to

ash pink (B).

3. When the equipment module receives

the pairing message, it will blink blue

repeatedly, then return to blinking

green.

4. The outdoor remote sensor will blink

green when it is paired, then the LED on

the outdoor sensor will turn o.

5. Install the outdoor sensor.

Battery types

• Alkaline AA batteries will perform well in most

applications.

• Lithium AA primary cell batteries are recommended

for cold climates. See the battery manufacturer product

specications for details.

• Rechargeable batteries are not recommended.

Set At

Menu

Zone

LEAVE

Menu

Zone

Specications

Installing Batteries

Establishing Communication

Mounting the Outdoor Sensor

Technician Setup and Warranty

3

5-7

2

1

4

After batteries are installed you will

see the light turn on for approximately

10 seconds. The light will briey

illuminate WHITE when batteries are

installed.

*PM-R250W-IM-2403*

PM-R250W-IM-2403

Mounting the Outdoor Remote Sensor

Do not install in direct sunlight.

For best results, install on a

north-facing wall, sheltered by

a roof overhang or something

similar.

IMPORTANT:

To install remove the front cover

and place a screw in the left and

right screw holes.

North Facing Wall

Roof Shelter

Produktspezifikationen