Proaim P-18 Bedienungsanleitung
Lies die bedienungsanleitung für Proaim P-18 (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Proaim P-18 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
What s In The Box’
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo copying, recording, or otherwise, except as may be expressly permied by the applicable copyright -
statutes or in wring by the Publisher.
Central Post
Weight Rod / Shank
Weight Closers
LCD Mounng Arm
Tools
1st Secon
2nd Secon
3rd Secon
4th Secon
5th Secon
18 t Film Crane Jib f Camera Arm (P-18)
A s s e m b l y M a n u a l
Storage Bag
2
Slide Central Post of Jib onto the Jib Stand and ghten knob to secure it. (Not Included) -2
Open shank from central post. Leave the black washers at one side. Then insert the end of Secon-3
inside Central Post. Align holes of Secon with Central Post to screw in the shank back.
Similarly, insert black washers onto other side and push the shank to ghten it with the dome nut.
Using a wrench, ghten the dome nut from both sides to secure them.
Camera Jib Setup
Knob 2
Secon 4 has connecng bars aached on both ends. Slide bars of Secon 4 into Secon 3 & ghten- - -
them together using provided allen key. Connue the Arm build by sliding in secon 2 onto secon 3,
secon 2 onto secon 1 and nally secon 5 onto secon 4 in the same way. Your jib arm is now com-
pletely connected.
Tighten the Wire Puller and its Central Pool Adapter. Tighten bolts to secure them.
Tighten Bolts
Connecng Bar
3
Connect the Wire/Cable Tensioner with cable.
Simply rotate the mid secon handle to ghten-
the cable adding required amount of strength to
the system.
NOTE: Once you discover correct balance, consider marking the weights for that parcular camera;
f
acilitang an easier set up the next me.
To accommodate all standard cameras, mulple
slots are provided for aachment on Camera
Plate.
Insert Weight Shank/Rod and standard exercise
Weights (Not Included) with a hole, according1”
to your camera setup requirements. Secure them
with Weight Closers.
You can easily mount any Pan Tilt Head
(Not Included) on the provided slots on camera
plate via screws. This assembly is accomplished
in Under slung Mode.
Removing Locking Pin from Central Post allows
you to frame mul dimensional lng shots by-
using Control Handle.
Produktspezifikationen
| Marke: | Proaim |
| Kategorie: | Nicht kategorisiert |
| Modell: | P-18 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Proaim P-18 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Proaim
3 Juli 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
5 September 2024
3 September 2024
Bedienungsanleitung Nicht kategorisiert
- Nowsonic
- Mofily
- Char-Broil
- Command
- Raspberry Pi
- RGV
- Corel
- ESE
- Icom
- Carnielli
- Devialet
- WHD
- Microboards
- Valera
- Magic Chef
Neueste Bedienungsanleitung für -Kategorien-
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025