Proaim P-G-PM Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Proaim P-G-PM (7 Seiten) in der Kategorie Stativ. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.3 Sternen bewertet
Seite 1/7
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Power Sucon Mount Camera Gripper (P G )- -PM
A s s e m b l y M a n u a l
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo copying, recording, or otherwise, except as may be expressly permied by the applicable copyright -
statutes or in wring by the Publisher.
What s In The Box’
2 x Sucon Cups
2 x Ropes
2 x Ropes Hooks
Camera Mounng
Plaorm
3 x Bowl Head
100mm Bowl
Adapter
3 x Sucon Cups with Cap
9 x Aluminum Rods
(Size: 30cm,15cm,7.5cm)
2 x Camera Mounng Bolts
(Size: 2 x 1/4” & 3/8”)
1 x L Type -
Allen Key (Size:4mm)
2
Camera Mount Gripper Setup
Remove the cap from the Sucon Cup, and
you will see thread located in the center, 1/4”
as shown in the image.
Remove the dust cover and posion the
sucon cup wherever required.
Screw in the Ball Tilt Head on sucon cups.
Adjustable Ball Tilt Heads allow for an
extensive range of lockable posions for
Aluminum Rods.
Pull and then remove the cap of the
aluminum rod (30cm).
Similarly, mount all the Ball Tilt heads onto
the sucon cups.
Press down the sucon cup and keep pushing
the pump to rmly x it on the surface.
Repeat this process for all the sucon cups.
Cauon: Recheck the Pump every 90 minutes.
If the red line is visible, Re pump the cup -
without losing the remaining vacuum ll the
Red Line disappears.
3 x Dierent Assembly Aluminum Rods
3
Screw the other end of the aluminum rod
(30cm) onto the Ball Tilt head, and then
ghten it.
First loosen the knob, then set the posion of
the Aluminum rods and nally secure them by
ghtening the knobs.
Screw the rods into the camera mounng
plaorm and ghten them.
Firstly, remove the dust cover and place your
sucon cup on the selected place and press
down to x the pump rmly on the surface.
Remove the cap of the aluminum rod (15cm),
then screw and ghten it properly onto the
Ball Tilt head. Repeat the same process for
aaching the other aluminum rods.
NOTE: Three rods are provided for each length
(30cm,15cm,7.5cm). These rods can be linked
together in any combinaon you need to create
the perfect setup.
Produktspezifikationen
| Marke: | Proaim |
| Kategorie: | Stativ |
| Modell: | P-G-PM |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Proaim P-G-PM benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Stativ Proaim
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
Bedienungsanleitung Stativ
- Stativ Kogan
- Stativ Zhiyun
- Stativ DJI
- Stativ Konig & Meyer
- Stativ Vanguard
- Stativ Braun
- Stativ Ulanzi
- Stativ Camgear
- Stativ FeiYu-Tech
- Stativ Rollei
- Stativ Fat Gecko
- Stativ Hama
- Stativ Celly
- Stativ SmallRig
- Stativ Revo
Neueste Bedienungsanleitung für -Kategorien-
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025