Rane ME 30B Bedienungsanleitung
Lies die bedienungsanleitung für Rane ME 30B (5 Seiten) kostenlos online; sie gehört zur Kategorie Mischer. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu Rane ME 30B oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/5
Manual-1
OPERATORS MANUAL ME 30B
microGRAPHIC EQUALIZER
QUICK START
If this is your first equalizer, please do yourself and your speakers a favor and read the complete manual. “An ounce of
prevention...,” and all that.
You may use either the 3-pin or ¼" TRS connector for Input or Output. Hook-up is intuitive. Just follow the
silkscreened instructions on the rear of the unit. Polarity convention is per IEC/ANSI/AES standards of pin 2 positive, pin 3
negative and pin 1 shield. The ME 30B does not invert the signal. Only connect one INPUT type per channel. The 3-pin
and ¼" TRS Inputs do not sum. You may, however, use both types of OUTPUTS simultanesously if desired.
Anyone familiar with other graphic equalizers finds the ME 30B just as familiar. Setting curves is as easy as it is on all
Rane graphics thanks to our innovative constant-Q circuitry. If you feel you want more information on setting up your
curves, please read on.
If you are familiar with equalizers, then hook-up, plug-in, turn-on and go!
ME 30B CONNECTION
When first connecting the ME 30B to other components,
leave the POWER switch off until the very last. This gives
you a chance to make mistakes and correct them without
damaging your fragile speakers, ears and nerves.
INPUTS
Both 3-pin and ¼" TRS Inputs are wired in parallel and
are actively balanced. Each works equally well. Choose
strictly from a required hardware point-of-view, there will be
no performance trade-offs. The wiring convention adheres to
American, British and International standards of pin 2 or tip
being hot, pin 3 or ring being return, and pin 1 or sleeve being
shield. Unbalanced operation involves using only pin 2 or tip
as signal, and pin 1 or sleeve as sheild or ground. It is not
necessary to short any inputs to ground—it doesn’t hurt, it’s
just not necessary. Use pin 1, or the shell, for shield ground.
OUTPUTS
The Outputs mimic the Inputs. Balanced output requires
using pin 2 or tip, and pin 3 or ring for the signal. It does not
require pin 1 or shield. The signal exists differentially
between the two balanced leads; ground is not involved. For
hum-free systems ground is used only for shielding.
EXPANDING
Expanding and/or daisychaining the Inputs and Outputs
normally uses the ¼" jacks. Three parallel Input connectors
allows driving a second signal processor or amplifier without
special cabling.
SIGNAL LEVELS
Signal levels from -10 dBV to +4 dBu are considered
normal and within range (at least 20 dB of headroom exists
above these levels). Do not directly connect microphones into
the ME 30B. These require a mic preamp.
Produktspezifikationen
| Marke: | Rane |
| Kategorie: | Mischer |
| Modell: | ME 30B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Rane ME 30B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Mischer Rane
8 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
Bedienungsanleitung Mischer
- Arendo
- ANT
- Bomann
- Alpina
- Chandler Limited
- Solac
- Taurus
- Korona
- Bodum
- HQ Power
- Day
- Monoprice
- Berlinger Haus
- JML
- ADB
Neueste Bedienungsanleitung für -Kategorien-
13 Januar 2026
12 Januar 2026
9 Januar 2026
31 Dezember 2026
25 Dezember 2025
16 Dezember 2025
16 Dezember 2025
7 Dezember 2025
4 Dezember 2025
27 November 2025