Sani-Lav 56FK2 Bedienungsanleitung
Sani-Lav
Spülbecken
56FK2
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sani-Lav 56FK2 (7 Seiten) in der Kategorie Spülbecken. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2.5 Benutzern mit durchschnittlich 5.0 Sternen bewertet
Seite 1/7
1
H A N D S - F R E E F L O O R M O U N T W A S H S TAT I O N
of Domestic and Foreign Parts
Operating Manual for 3-Person Hands-Free Floor Mount
Stainless Steel Wash Station
Models 56FK2 and 56FK2.5
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Low-Lead
2
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
H A N D S - F R E E F L O O R M O U N T W A S H S TAT I O N
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Installation Instructions
Step 1
1. 2 and 3-Person models require leg assembly.
2. Place wash station sink on leg assembly and secure with hardware (provided).
3. Establish sink location.
4. Mark the floor where the four holes are at the base as shown in illustration A.
5. Drill holes as required for mounting hardware. (Hardware not included).
Step 2
1. Install spout assembly to the sink.
2. Install elbow fitting (provided) to the spout assembly.
3. Connect one side of the supply line (provided) to the spout assembly.
4. Install strainer assembly.
Step 3
1. Install mixing check valve and elbow fitting to valve.
2. Install knee pedal valves under the sink if not mounted already.
3. Attach connecting tube from the spout to the knee pedal valve.
Step 4
1. Secure wash station to floor.
2. Connect waste line to strainer assembly.
3. Connect water supplies (hot and cold) to the mixing check valve.
Step 5
1. Remove aerator from the spout assembly and flush water line by pressing pedal for 30
seconds.
2. Check connections for leaks. Replace aerator onto the spout assembly.
3. Seal gap between bowl and leg assembly as shown in illustration B.
4. When mounting against wall, we recommend sealing top of backsplash to wall as shown in
illustration C.
Parts List
(1) Floor mount wash station
(1) Leg assembly set
(6) Nuts, bolts and washers for leg assembly
(4) Nuts and washers for connecting sink to leg assembly
(3) Double knee pedal valve
(6) Valve mounting nuts
(3) Swivel gooseneck spout with aerator
(3) Connecting tube for valve to spout connection
(6) Fittings, brass, 0.375” male compression and 0.375” male NPT
(1) Strainer assembly with basket
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
Go to for more information on replacement parts and installation videos.columbiasinks.com
Illustration A
Illustration B
Illustration C
3
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
H A N D S - F R E E F L O O R M O U N T W A S H S TAT I O N
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from spout
or valve stem assembly.
Flat washer on the
stem/plunger is worn.
To determine if the leak source is from the hot or cold side shut
cold water source off. See if water still leaks from the spout. If
leak continues then repair hot side if not repair cold side
We recommend installing valve repair
kit.
Water leaks from the
front of the valve.
O-Rings on the
plunger are worn out.
Visually determine whether the cold or hot side is leaking. We recommend replacing threaded
insert, plunger assembly & spring.
See illustrations below.
Valve Repair Instructions
Note: Valves are designed to be repaired without having to be disconnected from mount or plumbing.
1. Turn off water source. Do not remove valve from sink.
2. Remove pedal assembly using a 15/16” open end wrench or socket wrench. As shown in
illustration A.
3. Using a 1” deep socket wrench or closed end wrench remove insert assembly as shown in
illustration B.
4. Replace with new repair kit as shown on illustration C.
5. Reinstall pedal assembly and turn water source on.
Illustration A
Illustration B
Illustration C
Produktspezifikationen
| Marke: | Sani-Lav |
| Kategorie: | Spülbecken |
| Modell: | 56FK2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sani-Lav 56FK2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Spülbecken Sani-Lav
12 Juni 2025
12 Juni 2025
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
Bedienungsanleitung Spülbecken
- Spülbecken Gustavsberg
- Spülbecken Deante
- Spülbecken Oliveri
- Spülbecken Elkay
- Spülbecken Rangemaster
- Spülbecken Cookology
- Spülbecken Advance Tabco
- Spülbecken Kuchinox
- Spülbecken Eagle Group
- Spülbecken Concept
- Spülbecken CDA
- Spülbecken Krowne
- Spülbecken Schock
- Spülbecken BLANCO
- Spülbecken Artusi
Neueste Bedienungsanleitung für -Kategorien-
12 Juni 2025
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025