SSV Works GN-F65 Bedienungsanleitung
SSV Works
Lautsprecher
GN-F65
Lies die bedienungsanleitung für SSV Works GN-F65 (2 Seiten) kostenlos online; sie gehört zur Kategorie Lautsprecher. Dieses Handbuch wurde von 27 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 14 Bewertungen. Hast du eine Frage zu SSV Works GN-F65 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
GN-F65
Polaris General
6.5” Speaker Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All SSV Works
Speakers are covered by a limited 1 year warranty against defects in material or
workmanship. Labor for replacement of defective components is not covered.
Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
CREASE LINE
CREASE LINE
PASSENGER SID E
CREASE LINE
CREASE LINE
DRIVER SIDE
2. M6 x 1.0 Screws x 6
1. GN-F65 Enclosures
(1 pair)
4. Drll Template
3. M6 Washers x 6
- T-30 Torx Driver - Drill with 1/4” Drill bit - Scribe or Punch tool
A. Cut out the INSIDE template (Driver/Passenger) along the cut
line. Position the template on kick panel above the foot rest
making sure to line up arrows on template to the curves of the
panel as seen on image A.
B. Using a scribing tool, mark the center of the 3 drill points
illustrated on the template as shown on image B.
A B
C. Using a ¼ drill bit, drill holes for mounting of kick Pods .
E. Use the provided M6 screws and washers and loosely tighten
the pod in place through the drilled holes. Once all screws
have been loosely installed, tighten down by hand.
F. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier.
Connecting the GN-F65 using the pre-installed, two-pin
connector will require an optional SSV Works plug-&-play
harness (WP-H1149 - sold separately). If you are not using the
WP-H1149 harness, simply cut off the two-pin connector and
follow the wiring instruction below.
C
E F
D. Place enclosure in location for mounting.
D
GN-F65 © 2017 SSV Works, Oxnard, CA 93030 GN-F65 Rev. A 10-5-17
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct
connect the “+” to the “+” and the “-“to the “-“from
the speaker wire to the amplier. If using with an SSV
Works complete system refer to the amplier wiring
instructions for more detailed wiring information.
“+”
“+”
“
-
”
“
-
”
Produktspezifikationen
| Marke: | SSV Works |
| Kategorie: | Lautsprecher |
| Modell: | GN-F65 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit SSV Works GN-F65 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lautsprecher SSV Works
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
Bedienungsanleitung Lautsprecher
- Nevir
- TCL
- KRK Systems
- Homedics
- Massive
- Cabasse
- Quad
- Dali
- Elipson
- Fiodio
- Sound2Go
- SVS
- Sonifex
- Numark
- FiveO
Neueste Bedienungsanleitung für -Kategorien-
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025