StarTech.com VDSL-LAN-EXTENDER-1G Bedienungsanleitung

Lies die bedienungsanleitung für StarTech.com VDSL-LAN-EXTENDER-1G (2 Seiten) kostenlos online; sie gehört zur Kategorie WLAN-Repeater. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 5 Bewertungen. Hast du eine Frage zu StarTech.com VDSL-LAN-EXTENDER-1G oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: October 13, 2023

10/100/1000 Mbps VDSL2 Ethernet Extender Kit - 1km

Product Information

For the latest drivers/software, technical specications, and declarations of

conformance, please visit: www.StarTech.com/VDSL-LAN-EXTENDER-1G

Requirements

• Ethernet Device x 2

• RJ45 Ethernet Cables x 2

• RJ45 or RJ11 Cable x 1

Package Contents

• VDSL Extender x 2

• Mounting Bracket Kits x 2

• Power Supply x 2

• Quick-Start Guide x 1

Installation

(Optional) Mounting the VDSL Extender

Note: Before mounting the VDSL Extender make sure that the surface you are

mounting to is strong enough to support the VDSL Extender. It is recommended that

the VDSL Extender is mounted on a wall stud to provide the correct support.

1. Determine the Mounting Surface for the Local and Remote VDSL Extender.

2. Place the VDSL Extenders upside down to expose the Mounting Bracket Holes on

the VDSL Extenders. Align the Holes in the Mounting Brackets with the Holes on

the bottom of the VDSL Extenders.

3. Insert four Screws through each Mounting Bracket and into the VDSL Extender.

4. Tighten each Screw using a Phillips Head Screwdriver.

5. Mount the VDSL Extender to the desired Mounting Surface using the appropriate

Mounting Hardware (e.g. Wood Screws).

Install the VDSL Extender Kit

1. Position a VDSL Extender in each of the locations, local and remote.

2. Using DIP Switch 1, ensure that one VDSL Extender is in Master Mode (CO), and the

other is in Remote Mode (RT).

Note: If the DIP switches need to be adjusted after the initial setup, both VDSL

Extenders must be powered o before changing the DIP switch settings.

3. Plug in an RJ45 Ethernet Cable from the LAN Port on the local VDSL Extender to an

Ethernet Port on the local Ethernet Device.

4. Plug in an RJ45 Ethernet Cable from the LAN Port on the remote VDSL Extender to

an Ethernet Port on the remote Ethernet Device.

5. Plug in a RJ45 or RJ11 Cable from the VDSL2 Port of the local VDSL Extender, to the

VDSL2 Port of the remote VDSL Extender.

6. Connect the included Power Adapters to each of the VDSL Extenders.

Product ID

VDSL-LAN-EXTENDER-1G

ComponentFunction

1DIP Switches

• Set the Mode or change settings on the VDSL

Extenders

• Refer to DIP Switch Chart

2LAN Port

• Connect to an RJ45 Port on Local and Remote

Equipment

3LAN Status LEDs• Refer to the LED Chart

4VDSL2 Status LEDS• Refer to the LED Chart

5VDSL2 Port

• Use a RJ45 or RJ11 Cable to connect the Local

and Remote VDSL Extenders together

6Power Input Port

• Connect the included Power Adapter

• Located on the rear of each VDSL Extender

2

1345

Produktspezifikationen