Tiptop Audio Control Path Bedienungsanleitung
Tiptop Audio
Klaviatur
Control Path
Lies die bedienungsanleitung für Tiptop Audio Control Path (4 Seiten) kostenlos online; sie gehört zur Kategorie Klaviatur. Dieses Handbuch wurde von 8 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 4.5 Bewertungen. Hast du eine Frage zu Tiptop Audio Control Path oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
www.tiptopaudio.com/art
CONTROL PATH
EG OUT
VCA OUT
VCA IN
EG OUT
1 2
DLDL
01
Control Path Manual
Control Path consolidates the dynamics modules needed to build synth voices into
one low-cost, small, and easy-to-use module. In a typical synthesizer voice, there are
two envelope generators: one envelope dedicated to sound modification, like a
filter, and the other dedicated to the end-of-the-voice VCA, which controls the
volume when a key is pressed on a keyboard or a note is triggered from a
sequencer. Control Path includes both of these envelopes, along with the VCA.
Under the hood, it's all analog, made with the classic envelopes of the OBX (even
the modern replica OBXs don’t have that) and the excellent SSI2164 VCA.
Quick Start:
The left envelope is the one you will most likely patch to a Filter Cut-O CV-IN. The
right envelope has a built-in VCA internally tied to it; you will most likely take the
Filter audio out and patch it into the VCA IN.
The envelope on the right side is patched to the internal VCA but is also available
through its EG OUT jack for further use with other modules.
EG OUT
VCA OUT
VCA IN
EG OUT
1 2
DLDL
sound card
02
Adding Velocity:
Control Path also includes velocity control. Velocity is used to vary the voltage peak
of the envelopes, providing additional dynamic variations to your notes.
Velocity Trimmer Adjustments:
Velocity works seamlessly with Octopus because we ensured that both Velocity CV
changes and gate are sent out in tight sync. If these two signals are not
synchronized (as is the case with some Eurorack gear) and Velocity CV lags, arriving
after the envelope has already fired, the velocity change will be heard as an audio
click. Beneath each envelope, there is a small trimmer that you can use to help
compensate for this issue.
To adjust it, send a repetitive sequence where you can hear the clicks (make sure
you are not confusing natural sharp envelope attack clicks or wave discontinuity
clicks) and turn the trimmer clockwise until the clicks are either reduced or
completely gone. However, adding this compensation introduces a slight delay to
help 'hide' the source issue.
Regarding the trimmers, they are multi-turn; once they reach their maximum setting,
they will make a faint clicking sound. Be mindful of this to avoid rotating them too far,
as excessive rotation might wear out and damage the trimmer. To reset the trimmer
to its factory setting, rotate it counterclockwise until you hear the faint clicks again.
DETUNE
SD LOAD
CV
ART IN
VIBRATO
ART WAVETABLE
POSITION
GATE OUT
WAVEFORM
OUT
EG OUT
VC TA OU
VCA IN
EG OUT
1 2
DLDL
sound card
CH CONFIG
MONO 8
Produktspezifikationen
| Marke: | Tiptop Audio |
| Kategorie: | Klaviatur |
| Modell: | Control Path |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Tiptop Audio Control Path benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Klaviatur Tiptop Audio
26 Juni 2025
26 Juni 2025
26 Juni 2025
25 Juni 2025
25 Juni 2025
25 Juni 2025
25 Juni 2025
25 Juni 2025
25 Juni 2025
25 Juni 2025
Bedienungsanleitung Klaviatur
- IK Multimedia
- Native Instruments
- Medeli
- Yamaha
- Zagg
- Technics
- Brydge
- Polyend
- Fujitsu
- Renkforce
- Dell
- Black Box
- Cooler Master
- Kurzweil
- Mars Gaming
Neueste Bedienungsanleitung für -Kategorien-
30 Juni 2025
26 Juni 2025
23 Juni 2025
23 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
21 Juni 2025
21 Juni 2025