TK Audio TK-lizer 2 Bedienungsanleitung
TK Audio
Nicht kategorisiert
TK-lizer 2
Lies die bedienungsanleitung für TK Audio TK-lizer 2 (3 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 23 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 12 Bewertungen. Hast du eine Frage zu TK Audio TK-lizer 2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/3
www.tkaudio.se
TK-lizer 2
Mastering EQ with M/S function
Thank you for buying the TK-lizer 2, manufactured and hand-assembled in Sweden and
thoroughly tested before leaving the factory.
The TK-lizer 2 is inspired of the Baxandall circuit from the 50’s. It’s a dual three-band EQ with low
and high bands switchable between shelf or peak. It has a high-pass filter with 12dB/oct slope, and
of course a level control for fine adjustments of the output level. To make the EQ even more useful it’s
also equipped with a M/S circuit. All controls are stepped for easy repeatability.
The controls:The controls:
The controls:The controls:
The controls:
Low freq: 28Hz, 48Hz, 72Hz, 132Hz, 195Hz, 255Hz, switchable between shelf or peak.
Mid freq: 400Hz, 630Hz, 870Hz, 1.3kHz, 2.4kHz, 4.8kHz.
High freq: 4kHz, 7.2kHz, 12kHz, 16kHz, 20kHz, 25kHz, switchable between shelf or peak.
HPF freq: 20Hz, 25Hz, 30Hz, 35Hz, 40Hz, 45Hz, or 100Hz, 125Hz, 150Hz, 175Hz, 200Hz,
225Hz with the x5 switch activated. 12dB/octave.
Cut/boost: -4dB, -3dB, -2dB, -1dB, -0.5dB, 0dB, +0.5dB, +1dB, +2dB, +3dB, +4dB.
Level: -4dB, -3dB, -2dB, -1dB, -0.5dB, 0dB, +0.5dB, +1dB, +2dB, +3dB, +4dB.
EQ in/out.
M/S in/out.
Cue switch for separate monitoring of the mid or side signal.
M/S mode:M/S mode:
M/S mode:M/S mode:
M/S mode:
When you select M/S mode the signal is split into M=mid (L+R) and S=Side (L-R) before the EQ, after
the EQ the signal is decoded back to L and R again.
None of the center information as bass drum, bass and lead vocal is present in the S channel, only
panned signals as guitars, drums, keys etc. In M/S mode you can affect the M and S signal
separately.
By using the high pass filter in M/S mode you can affect the lower range in two ways.
1. HPF on M channel cuts the low energy in the signal. (L and R)
2. HPF on S channel, frequencies below the selected frequency will be in mono. This is used when
cutting records and also to get a more focused low range.
In M/S mode you can also use the level controls to alter the stereo images, more S channel will widen
the image and less S channel will reduce the stereo images.
To be able to hear better what you are doing in M/S mode you can use the M and S cue switch to
listening to the M channel or S channel alone. The cued signal will be feeded to both channels then.
Produktspezifikationen
| Marke: | TK Audio |
| Kategorie: | Nicht kategorisiert |
| Modell: | TK-lizer 2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit TK Audio TK-lizer 2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert TK Audio
3 Oktober 2025
8 Juni 2025
5 September 2024
3 September 2024
3 September 2024
28 August 2024
28 August 2024
21 August 2024
15 Dezember 2023
Bedienungsanleitung Nicht kategorisiert
- Lynx
- DayStar Filters
- Lafe
- NEO Tools
- Casalux
- Snoes
- Huzaro
- Daewoo
- Powertec
- JAYS
- Zgonc
- Koala
- TDX
- Smile
- Acoustic Solutions
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026