Vivanco UR 850 LCD Bedienungsanleitung

Lies die bedienungsanleitung für Vivanco UR 850 LCD (8 Seiten) kostenlos online; sie gehört zur Kategorie Fernbedienung. Dieses Handbuch wurde von 77 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 39 Bewertungen. Hast du eine Frage zu Vivanco UR 850 LCD oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

UR 850 LCD Universal Controller

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: 1hotli[email protected]e

(GB) Operating Instructions

Vivanco UR 850 LCD remote control for

practically all TV, audio, video and other

infrared-controllable devices

Inserting the batteries

Open the battery compartment on the back of the

device, push the flap down lightly and insert 2 AA

alkaline batteries. Make sure that the polarity on the

batteries and in the battery compartment correspond

(thick spring = cell at bottom = -) and then close the

lid carefully. – Use undamaged batteries only.

Adapting to devices

In order to control your devices you must adapt or

set the remote control to them. There are two ways

of doing so: direct control code entry or code

search.

If the UR 850 LCD does not understand you it

displays and you can then repeat the entry. ERROR

Direct control code entry

Example: setting the remote control for a Philips TV

set:

1. Switch on your device, e.g. the TV, set to any

station.

2. To prepare code entry, briefly press the SET

button in the bottom right corner of the keypad, then

the required device button, e.g. . A brand and a TV

code number appear, see diagram.

– You cannot enter

a new code if you have activated the code entry lock.

3. Select the brand of your device, in this

example Philips, with or  . The first available

code in the device list is displayed.

4. Press a few buttons to determine whether you

have found a suitable code. When the code

corresponds to your device, press and the OK

setting for this device is completed.

5. If the code you have found does work at all or

not properly, try another code by selecting the next

code for the brand using the or button, then  

test the code as described above under 4. and, if

successful, confirm with . OK

6. To set the remote control for other devices,

proceed in the same way. Instead of the device TV

button, press another button, e.g. , CBL/VCRSAT

(DVB-T, DECODER), , , , , DVD TUNER TAPE CD

AUX).

-Before setting a code and performing the subsequent test

for recording or playback devices, please insert a medium

(tape, CD, cassette, DVD, etc.).- You can interrupt code

entry at any time by pressing . EXIT

Code search

If the brand of your appliance is not in the list or

none of the codes given fits, we recommend the

automatic code search.

Your remote control finds the correct control settings

almost automatically in a few seconds:

1. Switch on the device to be controlled. For

example, a program number appears in the display

of your satellite receiver.

2. To start the code search, press and hold the

SETCODE SETUP button for approx. 3 seconds.

appears in the display. Confirm this function by

pressing . OK

3. then appears in the display. DEV SEARCH

Confirm this function by pressing .OK

– If DEV

SEARCHdoes not appear you can set the function with the

  or button.

4. Press the device button of the device to be

controlled, e.g. and confirm the function by DVD

pressing . OK

5. Then point the remote control at the device to

be controlled while the remote control emits a

different signal every 2 seconds. The ON/OFF

respective code number is shown in the display.

6. When your device reacts, press a few buttons

to determine whether you have found a suitable

code. If the code corresponds to your device, press

OK SUCCESS twice.appears in the display, then

you press the device button, e.g. , to confirm DVD

the entry. The setting for this device is now

completed.

7. If the code you have found does work at all or

not properly, press and EXIT DEV SEARCH

appears again. Then proceed again as described

under 3.

Please note: - You can reverse the search direction with the

 or button if you have reacted too slowly to a response

from the device. – The Menu buttons cannot by used for

testing. -Before setting a code and performing the

subsequent test for recording or playback devices, please

insert a medium (tape, CD, cassette, DVD, etc.).- You can

interrupt code entry at any time by pressing . EXIT

Other settings

Setting the time

1 Press and hold for 3 seconds, then set SET

CONFIGUREwith the or button. Confirm this  

function by pressing . OK

2 appears in the display. Confirm TIME SETUP

this function by pressing . OK

3 Enter the time using the number buttons and

confirm with the button. Then press OK EXIT

several times to quit the setting mode.

Set priority volume control

With this function you can determine a device

exclusively for volume control, e.g. your audio

amplifier. Then the buttons , nd VOL +VOL – a

always control the amplifier, regardless of which

device you are controlling.

1 Press and hold for 3 seconds, then set SET

CONFIGUREwith the or button. Confirm this  

function by pressing OK

2 appears in the display. Set TIME SETUP VOL

LOCKwith the or button. Confirm this function  

by pressing . OK

3 Select the device button, e.g. for the AUX

amplifier and set priority= using the or ON  

button. Confirm this function by pressing . OK

4 Then press several times to quit the EXIT

setting mode.

- You can cancel the priority setting using the same

procedure. Instead of , set for all devices. ON OFF

Produktspezifikationen