XU1 XCS-1200U Bedienungsanleitung

Lies die bedienungsanleitung für XU1 XCS-1200U (2 Seiten) kostenlos online; sie gehört zur Kategorie Säge . Dieses Handbuch wurde von 9 Personen als hilfreich bewertet und erhielt im Schnitt 3.5 Sterne aus 5 Bewertungen. Hast du eine Frage zu XU1 XCS-1200U oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

SAFETY

INSTRUCTIONS

ALWAYS WEAR EYE, FACE

AND EAR PROTECTION

When operating the tool

Electrical safety

Using an extension lead

Additional Safety Instructions

for Circular Saws

Keep the mains cable away from any moving parts or

accessories.

Never cover the ventilation slots in the tool.

Always use an approved extension lead suitable for

the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing.

Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always

unwind the lead completely. Use of an extension lead

not suitable for the power input of the tool or which is

damaged or defective may result in a risk of re and

electric shock.

The power supply for this product should be protected

by a residual current device (rated at 30mA or less).

A residual current device reduces the risk of electric

shock.

If the supply cord of this power tool is damaged, it

must be replaced by a specially prepared supply cord

available through the service organization.

Original Instructions

XCS

-

1200U

185mm

Circular

Saw

Safety instructions for all saws

Cutting procedures:

WARNING!

a) Keep hands away from cutting area and the

blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are

holding the saw, they cannot be cut by the blade.

b) Do not reach underneath the workpiece. The

guard cannot protect you from the blade below the

workpiece.

c) Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the blade

teeth should be visible below the workpiece.

22

d) Never hold piece being cut in your hands

or across your leg. Secure the workpiece to

a stable platform. It is important to support the

work properly to minimize body exposure, blade

binding, or loss of control.

e) Hold power tool by insulated gripping

surfaces when performing an operation where

the cutting tool may contact hidden wiring or

its own cord. Contact with a “live” wire will also

make exposed metal parts of the power tool “live”

and shock the operator.

f) When ripping always use a rip fence or

straight edge guide. This improves the accuracy

of cut and reduces the chance of blade binding.

g) Always use blades with correct size and

shape (diamond versus round) of arbour holes.

Blades that do not match the mounting hardware

of the saw will run eccentrically, causing loss of

control.

h) Never use damaged or incorrect blade

washers or bolt. The blade washers and bolt

were specially designed for your saw, for optimum

performance and safety of operation.

Further safety instructions for all saws

Causes and operator prevention of kickback:

• Kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece

toward the operator;

• When the blade is pinched or bound tightly by

the kerf closing down, the blade stalls and the

motor reaction drives the unit rapidly back toward

the operator;

• If the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade

to climb out of the kerf and jump back toward the

operator.

Kickback is the result of saw misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a rm grip with both hands on the

saw and position your arms to resist kickback

forces. Position your body to either side of the

blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but

kickback forces can be controlled by the operator,

if proper precautions are taken.

b) When blade is binding, or when interrupting

a cut for any reason, release the trigger and

hold the saw motionless in the material until

the blade comes to a complete stop. Never

attempt to remove the saw from the work or

pull the saw backward while the blade is in

motion or kickback may occur. Investigate and

take corrective actions to eliminate the cause of

blade binding.

c) When restarting a saw in the workpiece,

centre the saw blade in the kerf and check that

saw teeth are not engaged into the material. If

saw blade is binding, it may walk up or kickback

from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk

of blade pinching and kickback. Large panels

tend to sag under their own weight. Supports must

be placed under the panel on both sides, near the

line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Blunt or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking

levers must be tight and secure before making

cut. If blade adjustment shifts while cutting, it may

cause

binding and kickback.

g) Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions for saws with pendulum

guard

Lower guard function:

a) Check lower guard for proper closing

before each use. Do not operate the saw if

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and make

sure it moves freely and does not touch the blade

or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use. The lower guard may become

sluggish due to, gummy deposits, or a build-up of

debris.

c) Lower guard may be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard by

retracting handle and as soon as blade enters

the material, the lower guard must be released.

For all other sawing, the lower guard should

operate automatically.

d) Always observe that the lower guard is

covering the blade before placing saw down

on bench or oor.An unprotected, coasting blade

will cause the saw to walk backwards, cutting

whatever is in its path. Be aware of the time it

takes for the blade to stop after switch is released.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a

stable platform. It is important to support the

work properly to minimize body exposure,

blade binding, or loss of control.

Young children should be supervised

to ensure that they do not play with the

appliance.

Do not use the tool with abrasive or masonry/

wet diamond wheels.

Only use blade diameter(s) in accordance with

the markings on the tool.

Yang/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Circular Saw XCS-1200U (XU1)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X

2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X

2011/65/EU

X

2006/42/EC

Annex IV

Notied Body:

Notied Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured L

WA

= dB (A); guaranteed L

WA

= dB (A)

P = KW; L/Ø = cm

Notied Body:

2012/46/EU

Emission No.:

Standard references: EN 60745-1; EN 60745-2-5;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 29.09.2017

First CE: 17 Archive-File/Record: NAPR017010

Art.-No.: 30.001.27 I.-No.: 11017 Documents registrar: Alex Kurz

Subject to change without noticeWiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

3000127_11017_XCS_1200U.indd 13502.10.2017 10:22:42

XU1 Power tools

XCS-1200U 0917

Telephone: GB: 0151 294 4488 / IRL: 1850 882711

This tool is double insulated; therefore no

earth wire is required.

Before you connect the charger to the mains supply

make sure that the data on the rating plate are identical

to the mains data.

General Power Tool Safety

Warnings

WARNING! Read all safety

warnings and all instructions. Failure

to follow the warnings and instructions may

result in electric shock, re and/or serious

injury.

Save all warnings and instructions

for future reference. The term “power

tool” in all of the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while

operating a power tool. Distractions can cause you

to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodied plugs and

matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is

an increased risk of electric shock if your body is earthed

or grounded.

c. Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

d. Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil,

sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of

electric shock.

f. If operating a power tool in a damp location

is unavoidable, use a residual current

device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you

are tired or under the inuence of drugs,

alcohol or medication.A moment of inattention

while operating power tools may result in serious

personal injury.

b. Use personal protective equipment. Always

wear eye protection. Protective equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying

power tools with your nger on the switch or energising

power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before

turning the power tool on.A wrench or a key left

attached to a rotating part of the power tool may result in

personal injury.

e. Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from

frequent use of tools allow you to become

complacent and ignore tool safety

principles.A careless action can cause severe injury

within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the rate for

which it was designed.

b. Do not use the power tool if the switch does

not turn it on and off.Any power tool that cannot

be controlled with the switch is dangerous and must be

repaired.

c. Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power tool accidentally.

d. Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools and accessories.

Check for misalignment or binding of

moving parts, breakage of parts and any

other condition that may affect the power

tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

5. Service

a. Have your power tool serviced by a

qualied repair person using only identical

replacement parts. This will ensure that the safety

of the power tool is maintained.

Description of symbols

Wear eye protection

Double insulated (Protection Class II)

Danger! - Read the operating instructions to

reduce the risk of inquiry

Caution! Wear ear-muffs. The impact of noise

can cause damage to hearing.

Caution! Wear a breathing mask. Dust which

is injurious to health can be generated when

working on wood and other materials. Never use

the device to work on any materials containing

asbestos!

SOUND AND VIBRATION

Danger!

Sound and vibration

Sound and vibration values were measured in

accordance with EN 60745.

L

pA

Sound Pressure Level: 82.70 dB(A)

K

pA

Uncertainty: 3 dB

L

WA

Sound Power Level: 93.70 dB(A)

K

WA

Uncertainty: 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)

determined in accordance with EN 60745.

Handle

Vibration Emission Value a

h

: 22.20 m/s²

K Uncertainty: 1.5 m/s²

Additional Handle

Vibration Emission Value a

h

: 1.27 m/s²

K Uncertainty: 1.5 m/s²

The specied vibration value was established in

accordance with a standardized testing method. It

may change according to how the electric equipment

is used and may exceed the specied value in

exceptional circumstances.

The specied vibration value can be used to compare

the equipment with other electric power tools.

The specied vibration value can be used for initial

assessment of a harmful effect.

Keep the noise emissions and vibrations

to a minimum.

•

Only use appliances which are in perfect working

order.

•

Service and clean the appliance regularly.

•

Adapt your working style to suit the appliance.

•

Do not overload the appliance.

•

Have the appliance serviced whenever necessary.

•

Switch the appliance off when it is not in use.

•

Wear protective gloves.

For EU countries only

Never place any electric power tools in your household

refuse.

To comply with European Directive 2012/19/EC concerning

old electric and electronic equipment and its implementation

in national laws, old electric power tools have to be separated

from other waste and disposed of in an environment-friendly

fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the

manufacturer, the owner of the electrical equipment must

make sure that the equipment is properly disposed of if p1-he

no longer wants to keep the equipment. The old equipment

can be returned to a suitable collection point that will dispose

of the equipment in accordance with the national recycling

and waste disposal regulations. This does not apply to any

accessories or aids without electrical components supplied

with the old equipment.

Subject to technical changes

Produktspezifikationen