CDN IN482 Bedienungsanleitung
Seiten 4 Thermometer
Lies die Bedienungsanleitung für CDN IN482 kostenlos online oder lade das PDF herunter. 49 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
Model: IN482
INFRARED THERMOMETER, TIMER & CLOCK
-67 to 482°F/-55 to +250°C; 24 hours by hr/min/sec
FOR NON-CONTACT SURFACE
TEMPERATURES
•1-second response
•Maximum, minimum and lock
for continuous scanning
•Distance:Spot = 5:1
•±3.6°F/2°C accuracy
•Stopwatch timer
•Clock
•Ambient temperature in standby mode
•Data-hold
•One-button operation
•Battery status indication
•Food-safe ABS plastic
•Auto-off
•2-way mounting: stand/loop
•3V Button IEC CR2032 Lithium (included)
Simply point toward the target and press the scan
button to get a quick reading of surface temperatures.
Note: Remove label from display before initial use.
Note: In the following instructions, names of the control
buttons are shown in CAPS. Function information that
appears on the display is shown in .BOLD CAPS
BATTERY INSTALLATION
Power off the unit before installing the battery.
A malfunction may occur if the power is on when
the battery is installed. If a malfunction occurs,
restart the device.
1. Turn the battery cover at the back of the unit
clockwise and lift off.
2. Install one 3V IEC CR2032 lithium button battery
with positive (+) side up by hooking it into the
battery housing. Press the battery down until
it clicks.
3. Replace the battery cover by turning it counter
clockwise until it clicks shut.
OPERATING INSTRUCTIONS
A. On/Off
1.
Press the SCAN button to turn the thermometer on.
B. Auto Off
The thermometer automatically turns off after
15 seconds of inactivity when the clock is not set.
Note: Auto-off is disabled when the clock has been set.
C. Set Clock
Once the clock is set, the time and ambient
temperature appear on the display when the
thermometer is not in use.
Note: Auto-off is disabled when the clock has been set.
1.
Press the SCAN button to turn the thermometer on.
2. Press the MODE button seven times
to enter Set Clock mode. The SET
icon () ashes in the upper right
corner of the display.
3. Press the SCAN button to choose between
12-hour and 24-hour display. ashes on the 24
display. Press the SCAN button again to change
between 12-hour and 24-hour display.
4. Press the MODE button to conrm the time
format and set the hour. The hour digits ash.
5. While the hour digits are ashing, press the
SCAN button to enter the correct time.
PO Box 10947 Portland, OR 97296-0947 800 338-5594 800 879-2364 TelFaxWeb CDNkitchen.com
Produktspezifikationen
| Marke: | CDN |
| Kategorie: | Thermometer |
| Modell: | IN482 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit CDN IN482 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Thermometer CDN
CDN TCG400 Bedienungsanleitung CDN TCH130 Bedienungsanleitung CDN DTL572 Bedienungsanleitung CDN DTP392 Bedienungsanleitung CDN IN1022 Bedienungsanleitung CDN TCF400 Bedienungsanleitung CDN IRL500 Bedienungsanleitung CDN ProAccurate DT450X Bedienungsanleitung
Alle CDN Thermometer Bedienungsanleitungen
Beliebt in Thermometer
CDN ProAccurateDOT2 Bedienungsanleitung CDN EOT1 Bedienungsanleitung CDN ProAccurate POT750X Bedienungsanleitung
Bedienungsanleitung Thermometer
Neueste Bedienungsanleitungen für Thermometer
TFA 30.1043.02 Bedienungsanleitung TFA BodyTemp 478 Bedienungsanleitung TFA 30.1060.05 Bedienungsanleitung TFA 30.3060.01 Bedienungsanleitung TFA 30.1027 Bedienungsanleitung Tefal BH1550 Bedienungsanleitung EMOS E0558P Bedienungsanleitung Uni-T UT302D Bedienungsanleitung Lionelo FeverScan Bedienungsanleitung Yato YT-72971 Bedienungsanleitung