Festo DAMH-L8-20-PL-1 Bedienungsanleitung

Lies die bedienungsanleitung für Festo DAMH-L8-20-PL-1 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 31 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 16 Bewertungen. Hast du eine Frage zu Festo DAMH-L8-20-PL-1 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Assembly instructions (Original instructions)

8070340

2017-07

[8070342]

†‡

Profile mounting

DAMH-L8-...-PL-1

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

1.Further applicable documents

All available documents for the product www.f

esto.com/pk

Operating instructions of the linear actuator 7

2.Safety

Switch off power supply and compressed air before mounting work.

Observe further applicable documents.

Comply with tightening torques ( Table).

3.Intended use

Fastening of two linear actuators 7 to a mounting surface.

4.Scope of delivery

18446d_1

1Profile mounting

2Sleeve

3Screw

4Screw

5Knurled nut

6Nut

(2x)

(2x)

(1x)

(1x)

(1x)

(1x)

5.Not in scope of delivery

18446d_2

7Linear actuator

DLGF

8Screw

(2x)

(4x)

6.Mounting

Determine the mounting points ( Further applicable documents).

18446d_3

Position actuators 7

flush with each other.

Place a knurled nut 5

into the drill hole (A) of

a determined fastening

point.

Lightly clamp the

actuators 7 into place

with the screw 4 and

knurled nut 5.

Place the sleeves 2

into the drill holes of the

profile mountings 1.

Push the screw 3 through

the sleeves 2, profile

mountings 1 and drill

holes (B) as shown.

18446d_4

Clamp the profile

mountings 1 to the

actuator 7 using the

hex nut 6.

Align the profile

mounting 1 parallel

to the actuators 7.

Tighten the hex nut 6.

Tighten the screw 4.

Repeat the mounting steps

for all mounting points.

18446d_5

Attach the profile

mountings 1 to the

mounting surface using

2 screws 8.

7.Screw sizes and tightening torques M

A

1)

Information

Select screws 8 suitable for the installation situation.

DAMH-L8-...-PL-120253240

3Screw M4x60 M5x70 M6x90 M6x110

[Nm] 2.25.08.59.0

4Screw M4x35 M5x45 M6x55 M6x70

[Nm] 2.25.08.59.0

6Nut M4M5M6M6

[Nm] 2.25.08.59.0

8Screw M4M5M6M6

1)

Tolerances for tightening torques M

A

without indication of tolerance

M

A

. 3 Nm: ± 10 %

M

A

, 3 Nm: ± 20 %

7

7

7

8

6

4

8

1

2

3

5

7

4

2

3

1

2

1

5

A

B

B

6

1

1

4

Produktspezifikationen