Forte Lighting 2743-03 Bedienungsanleitung
Seiten 1 Beleuchtung
Lies die Bedienungsanleitung für Forte Lighting 2743-03 kostenlos online oder lade das PDF herunter. 27 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
2743-03 2743-06
Connect the lamp holder (N) to the lamp holder (P) and lock it
with (T). Secure shade (Q) onto the socket (O) by screwing
socket ring (R) tightly. Install light bulb (not included) in
accordance with the fixture’s specifications. Do not exceed
the recommended maximum wattage.
Carefully remove all contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old fixture from the
ceiling, including the old crossbar. Remove the crossbar
assembly from the bag. Crossbar (B) contains several
pairs of threaded holes. Find the pair of holes that matches
the spacing of the holes on the junction box and the fixture’s
canopy. Two mounting screws (A) should be attached to
crossbar (B). You may need to tighten nuts (C) to hold these
screws in place. Pull the house wires through the center of
crossbar (B). Place crossbar (B) over the junction box so
that mounting screws (A) are vertical and aligned with
the hole locations on the fixture’s canopy (F). Secure
crossbar (B) to the junction box by tightening the screws.
crossbar
crossbar
There are an 18 inch rod (K), a 12 inch rod (L), and a 6
inch rod (M) included for each fixture. Rod (L) is wired.
Determine the correct number of rods needed for proper
hanging height. To lengthen the fixture, add additional rods.
If additional rods are needed, contact the place of purchase
to order. To shorten the fixture, trim the wires to the desired
length, leave at least 8 to 10 inches of wire in addition to the
desired length and slide any excess rods off to discard. Keep
in mind that you must use at least the provided 6 inch rod (M)
Push canopy (F) up to the ceiling and tighten the deco nuts (H)
onto the exposed mounting screws (A).
to hang the fixture. Thread the wires through the rods and
pull the wires until taut before connecting the rods together.
Thread bottom rod (M) onto nipple (N) on the fixture. Thread
the nipple of the top rod onto swivel post (I) of canopy (F).
Pull the fixture wires through the top of the canopy.
SMOOTH
o
P
T
Produktspezifikationen
| Marke: | Forte Lighting |
| Kategorie: | Beleuchtung |
| Modell: | 2743-03 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Forte Lighting 2743-03 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beleuchtung Forte Lighting
Forte Lighting 2748-05 Bedienungsanleitung Forte Lighting 2664-04 Bedienungsanleitung Forte Lighting 7120-05 Bedienungsanleitung Forte Lighting 7116-01 Bedienungsanleitung Forte Lighting 2743-06 Bedienungsanleitung Forte Lighting 2672-01 Bedienungsanleitung Forte Lighting 2759-03 Bedienungsanleitung Forte Lighting 2179-01 Bedienungsanleitung
Alle Forte Lighting Beleuchtung Bedienungsanleitungen
Beliebt in Beleuchtung
Forte Lighting 2688-01 Bedienungsanleitung Forte Lighting 7096-06 Bedienungsanleitung Forte Lighting 5535-01 Bedienungsanleitung
Bedienungsanleitung Beleuchtung
Neueste Bedienungsanleitungen für Beleuchtung
IKEA GÖMPYSSLING 106.151.59 Bedienungsanleitung Robert Abbey EG42X Bedienungsanleitung Robert Abbey CI42X Bedienungsanleitung Robert Abbey OB43X Bedienungsanleitung Robert Abbey CR20X Bedienungsanleitung IKEA VINDKRAFT 606.013.05 Bedienungsanleitung Robert Abbey 463 Bedienungsanleitung Robert Abbey D1988 Bedienungsanleitung Robert Abbey Z1000 Bedienungsanleitung Halsey Taylor MFWS230 Bedienungsanleitung