Kichler Midi 52649CPZ Bedienungsanleitung

Lies die bedienungsanleitung für Kichler Midi 52649CPZ (3 Seiten) kostenlos online; sie gehört zur Kategorie Beleuchtung. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 7 Bewertungen. Hast du eine Frage zu Kichler Midi 52649CPZ oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

1. Remove knobs[C] and lock washers[D] from the mounting screws that

are preinstalled to mounting strap[G]. Retain knobs and lock washers.

2. Attach mounting strap[G] to outlet box[I] using the strap mounting

screws[H]. Mounting strap can be adjusted to suit position of fixture.

3. Grounding instructions: (See Illus. a or b).

a. On fixtures where mounting strap is provided with a hole and two

raised dimples, wrap ground wire from outlet box around green

ground screw, and thread into hole.

b. On fixtures where a cupped washer is provided, attach ground wire

from outlet box under cupped washer and green ground screw, and

thread into mounting strap.

Fixture is provided with two (2) ground wires. Connect fixture ground

wires to outlet box ground wire with wire connector after following the

above steps. Never connect ground wire to black or white power supply

wires.

4. Make wire connections. Reference chart below for correct connections

and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

BlackWhite

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or Black

without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth (See illus.)Neutral Wire

5. NOTE: Fixture should be installed in the down position

(light shines downward) ONLY.

Push fixture to wall, carefully aligning the mounting screws protruding

from the mounting strap with holes in canopy.

NOTE: Make sure all wires are inside canopy and do not get pinched

between mounting strap and canopy, or wall and canopy of fixture.

6. Slip lock washers[D] over threads protruding through holes in canopy (2

places).

7. Screw knobs[C] onto threads protruding through holes in canopy (2

places) and tighten to secure fixture to wall.

8. Adjust shade[A] (Fig. 1) by loosening adjustment screw[B] at the fixture

joint (turn slightly counterclockwise), adjusting shade to desired position,

then re-tightening adjustment screw (turn slightly clockwise). DO NOT

COMPLETELY REMOVE THE ADJUSTMENT SCREW FROM THE

FIXTURE JOINT.

9. Insert recommended bulb(s) (not included).

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLETBOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLETBOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

a

b

For warranty information please visit: kichler.com/warranty

REV 2-AUG-2023

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the

installation.

CAUTION:

• This fixture is intended for use with LED Bulb(s) ONLY.

WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC)

and all local code specifications. If you are not familiar with code requirements, installation by a

certified electrician is recommended. Failure to adhere to these codes and instructions may result

in serious injury and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

FIXTURE DIAGRAM

SPACER

IS-52649-US

PARTS LIST

[A] Shade

[B] Adjustment Screw

[C] Knob (2)

[D] Lock Washer (2)

[E] Canopy

[F] Mounting Screw (2)

[G] Mounting Strap

[H] Strap Mounting Screw (2)

[I] Outlet Box (not supplied)

SPACER

INSTALLATION INSTRUCTIONS

I

E

C

D

A

B

H

G

F

I

E

C

D

A

B

H

G

F

SPACER

Fig. 1

NOTE:

BULB(S) NOT INCLUDED

USE 13 WATT MAX

T10 LED BULBS ONLY

Produktspezifikationen