Little Giant 508058 Bedienungsanleitung

Lies die bedienungsanleitung für Little Giant 508058 (8 Seiten) kostenlos online; sie gehört zur Kategorie Pumpe. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu Little Giant 508058 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

G SAFETY GUIDELINES

READ ALL INSTRUCTIONS AND SAFETY GUIDELINES

THOROUGHLY. FAILURE TO FOLLOW THE GUIDELINES AND

THE INSTRUCTIONS COULD RESULT IN SERIOUS BODILY

INJURY AND/OR PROPERTY DAMAGE.

1. CAUTION: To reduce the risk of electrical shock, pull plug

before servicing this pump.

2. Check local electrical and building codes before installation.

The installation must be in accordance with their regulations.

3. During normal operation the sump pump is immersed in

water. Also, during rain storms, water may be present in the

surrounding area of the pump. Caution must be used to pre-

vent bodily injury when working near the pump:

a. Electrical power should be disconnected prior to touching,

servicing or repairing the pump.

b. To minimize possible fatal electrical shock hazard, extreme

care should be used when changing fuses. Do not stand in

water while changing fuses or insert your finger into the fuse

socket.

4. Do not run the pump in a dry sump. If the pump is run in a

dry sump, the surface temperature of the pump will rise to a

high level. This high level could cause skin burns if the pump

is touched and will cause serious damage to your pump.

5. Do not oil the motor. The pump housing is sealed. A high

grade dielectric oil devoid of water has been put into the motor

housing at the factory. Use of other oil could cause serious

electric shock and/or permanent damage to the pump.

6. This pump’s motor housing is filled with a dielectric lubricant

at the factory for optimum motor heat transfer and lifetime

lubrication of the bearings. Use of any other lubricant could

cause damage and void the warranty. This lubricant is non-

toxic; however, if it escapes the motor housing, it should be

removed from the surface quickly by placing newspapers or

other absorbent material on the water surface to soak it up, so

aquatic life is undisturbed.

7. In any installation where property damage and/or personal

injury might result from an inoperative or leaking pump due to

power outages, discharge line blockage, or any other reason,

a backup system(s) and/or alarm should be used.

RISK OF ELECTRIC SHOCK—This pump is supplied with a

grounding conductor and grounding-type attachment plug. To

reduce the risk of electric shock, be certain that it is connected

only to a properly grounded, grounding-type receptacle. As a

safety measure, each electrical outlet should be checked with an

Underwriters Laboratory Listed circuit analyzer. This will indicate

if the power, neutral and ground wires are properly connected. If

they are not, call a qualified licensed electrician.

ELECTRICAL CONNECTIONS (FIGURE 1)

Your sump pump is supplied with a 3-prong electrical plug. The

third prong is to ground the pump to prevent possible electric

shock hazard. Do not remove the third prong from the plug. A

separate branch electrical circuit is recommended. Do not use an

extension cord.

Figure 1.

INSTALLATION (FIG. 2)

1. Clean any debris from sump pit and set pump in center of pit.

A solid bottom will prevent clogging of the pump from sand

and dirt.

2. Connect discharge piping and run it to the nearest sewer or

surface outlet. Use pipe joint compound at all connections.

Sump pumps can be piped to discharge into the house drain-

age system, to a dry well, splash block or to a storm drain,

depending on local plumbing codes. The discharge pipe

should be as short as possible and contain as few elbows as

possible. The discharge pipe should be the same diameter

as the discharge size to reduce pipe friction losses. Smaller

pipe will restrict capacity and reduce pump performance. The

sump pump comes with 1½” female pipe thread discharge,

and 1-1/4” FNPT reducing bushing.

3. Always install a union in the discharge line, just above the

sump pit to allow for easy removal of the pump for cleaning or

repair.

1

Little Giant

P. O. Box 12010

Oklahoma City, OK 73157-2010

405.947.2511 • Fax: 405.947.8720

www.LittleGiantPump.com

CustomerService-[email protected]

8-CIM, 8-CBM

6-CIA, 8-CIA, 8-CBA

Produktspezifikationen