Little Giant Pit+Plus Jr Bedienungsanleitung
Little Giant
Wasserpumpe
Pit+Plus Jr
Lies die bedienungsanleitung für Little Giant Pit+Plus Jr (20 Seiten) kostenlos online; sie gehört zur Kategorie Wasserpumpe. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Little Giant Pit+Plus Jr oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/20
Pit+Plus JR & SR Systems
OWNER'S MANUAL
English
EN
Pit+Plus JR and SR systems are designed for use in residential
applications to collect sewage, effluent, drainage, or seepage
water. These systems divert this away from structures, land-
scapes prone to erosion, and areas with poor drainage. Install
only in indoor applications, isolated from traffic.
The system is equipped with floats or an External Control Mod-
ule (ECM™). The ECM™ is an advanced control switch for a sew-
age basin.
This product is covered by a Limited Warranty for a period of 3 years from the date of original purchase by
the consumer. For complete warranty information, refer to www.LittleGiant.com
.
Specifications
SAFETY INSTRUCTIONS
This equipment should be installed and serviced by technically qualified personnel who are familiar with
the correct selection and use of appropriate tools, equipment, and procedures. Failure to comply with
national and local electrical and plumbing codes and within Little Giant recommendations may result in
electrical shock or fire hazard, unsatisfactory performance, or equipment failure.
Know the product’s application, limitations, and potential hazards. Read and follow instructions and those
provided with the pump carefully to avoid injury and property damage. Do not disassemble or repair unit
unless described in this manual.
Failure to follow installation or operation procedures and all applicable codes may result in the following
hazards:
HP Volts Hz Amps
Discharge
in (mm)
Watts
Shut Off
ft (m)
4/10
115 60
8 - 870 20 (6.1)
1/2
11 2 (51)
1230 25 (7.62)
11.5 3 (76.2)
1 12.5 2 (51) 1330 53 (16.15)
Risk of severe injury or death by electrical shock.
• Check local electrical and building codes before installation. The installation must be in accordance with their
regulations as well as the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act
(OSHA).
• This product is supplied with a grounding conductor and grounding-type attachment plug. To reduce risk of elec-
tric shock, be certain that it is connected only to a properly grounded grounding-type receptacle. Do not remove
the third prong from the plug. The third prong is to ground the pump to help prevent possible electric shock haz-
ard. Do not use an extension cord.
INSTALLATION
Physical Installation
2
INSTALLATION
Physical Installation
1. Place the system indoors, in an isolated area away from foot traffic, as the covers are not suitable for
heavy traffic loads.
2. Remove cover and set aside.
3. Remove bolts and washers from pump access cover and set cover aside.
4. Make sure the pump is upright and standoff feet are located within the three integral torque stops.
5. Verify the pump discharge pipe is securely connected to the exit pipe inside the basin with the flex-
ible coupling.
6. Reconnect the pump discharge pipe with flexible coupling and band clamps, if necessary.
7. Examine the level control float switch and alarm float, if included.
• Make sure the float pole is secured to bottom of control cover and there are no obstructions.
• Refer to the float switch and/or alarm switch instruction manuals.
IMPORTANT: Do not change the lengths of the float pole assembly’s cord grips.
8. For systems with an ECM™, make sure the sensor tube extending from bottom of control module is
not damaged and unobstructed to allow air to pass through the vent tube.
9. Install piping.
• Remove temporary pipe caps from the vent and discharge pipes.
• Connect the basin discharge pipe to drain pipe.
• Install a check valve (not included) near the basin, horizontally or at an angle less than 45°.
• Drill a 3/16” hole in the discharge pipe, approximately 2” above discharge connections.
• Connect the Pit+Plus vent pipe to the vent pipe.
10. Make electrical connections.
• Insert piggyback plug to a 115 V outlet.
• Plug the pump power cord into back of piggyback plug.
Risk of bodily injury, electric shock, or equipment damage.
• This equipment must not be used by children or persons with reduced physical, sensory or mental abilities, or
lacking in experience and expertise, unless supervised or instructed. Children may not use the equipment, nor
may they play with the unit or in the immediate vicinity.
• Do not run the pump dry. If run dry, the surface temperature of the pump will rise to a high temperature that
could cause skin burns if touched and will cause serious damage to your pump.
• Operation of this equipment requires detailed installation and operation instructions provided in this manual for
use with this product. Read entire manual before starting installation and operation. End User should receive and
retain manual for future use. Keep safety labels clean and in good condition. Keep work area clean, well-lit, and
uncluttered.
• Wear safety glasses while installing or performing maintenance on the pump.
Produktspezifikationen
| Marke: | Little Giant |
| Kategorie: | Wasserpumpe |
| Modell: | Pit+Plus Jr |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Little Giant Pit+Plus Jr benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Wasserpumpe Little Giant
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
Bedienungsanleitung Wasserpumpe
- Grizzly
- Neptun
- Scheppach
- Makita
- AquaForte
- AL-KO
- Yato
- Metabo
- Flojet
- Trotec
- Tetra
- Flotide
- DAB
- Cocraft
- Hydro-Pro
Neueste Bedienungsanleitung für -Kategorien-
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025