PAC AP4-GM71 Bedienungsanleitung
Lies die bedienungsanleitung für PAC AP4-GM71 (5 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 33 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 17 Bewertungen. Hast du eine Frage zu PAC AP4-GM71 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/5
© 2024 Stinger. All rights reserved.
PAC-audio.com
C
Page 1
Rev: 1
Date:090924
Advanced Amplier Interface for
General Motors
AP4-GM71
The AP4-GM71 provides a 6-channel pre-amp output for use with aftermarket audio equipment. The AP4-GM71
delivers a variable 5v RMS pre-amp output with fading, balance, equalization, and level control capabilities. The
module also retains all audio from other vehicle features such as factory navigation prompts, Bluetooth, OnStar, and
parking sensor chimes. A data controlled remote amplier turn on wire is also provided by the AP4-GM71. The module
also provides a variable 2-channel ber optic digital audio output (TOSLINK).
Introduction and Features
Important Notes
1. This interface is only compatible in vehicles with Bose that are equipped with IOS, IOT and IOK Infotainment.
2. The factory amplier must be disconected and removed from the vehicle when the AmpPRO has been installed.
3. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
4. Channel 5 & 6 are a non-fading outputs. The outputs level of channel 5 & 6 can be controlled using the supplied level
control knob.
5. When the non-fading level control knob is not connected to the AP4-GM71, the output level of channels 5 & 6 will default to
100 percent.
6. To adjust mininum volume or chime volume without using the PC APP the level control knob must be connected.
7. The chime volume and minimum volume levels are set to a sutiable level by default. If you are happy with this level in your
particular application, then additional adjustment is not required. Please refer to the Setup and Conguration section on
page 2 for more details.
8. The factory radio's speed controlled volume and surround sound mode are not supported by the AP4 outputs.
9. When using the TOSLINK output, all chimes must be routed through the front output by setting DIP switch 1 on (down).
10. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to
a PC.
11. The AP4-GM71 is designed to be installed in the factory amplier location not behind the radio. It will replace the factory
amplier and it will no longer be used.
Wiring Connection Chart
Remote Turn On Output
2A Max Output
Front
1/L
2/R
4/R
5 6
3/L
Rear
Sub
TOSLINK
Speaker
Leads
1-3
AP4-GM71-HAR (A) or (B) Based on Data Type (SEE MANUAL)
To Vehicle
Amplier Harness
Non-Fading
Level Control
Knob
AP4-GM71-HAR (D)
To Aftermarket
Amplifier
Speaker
Leads
4-11
AP4-GM71-HAR (C)
Produktspezifikationen
| Marke: | PAC |
| Kategorie: | Empfänger |
| Modell: | AP4-GM71 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit PAC AP4-GM71 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger PAC
1 August 2025
31 Juli 2025
11 Juli 2025
10 Juli 2025
10 Juli 2025
12 August 2024
Bedienungsanleitung Empfänger
- Sunstech
- Skar Audio
- Smartwares
- Crunch
- Ecler
- Goobay
- Megasat
- Aiwa
- Roswell
- Zalman
- Pharos
- Lindell Audio
- Icom
- Hughes & Kettner
- Musical Fidelity
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
20 Januar 2026
20 Januar 2026
18 Januar 2026
17 Januar 2026
16 Januar 2026
16 Januar 2026
16 Januar 2026
16 Januar 2026
15 Januar 2026