PAC OnStar OS-311 Bedienungsanleitung

Lies die bedienungsanleitung für PAC OnStar OS-311 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 38 Personen als hilfreich bewertet und erhielt im Schnitt 3.6 Sterne aus 19.5 Bewertungen. Hast du eine Frage zu PAC OnStar OS-311 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705

[email protected] • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com

Page1

04-27-07

The OS-311 is a plug and play interface that allows replacement of a General Motors GMLAN factory radio. It will maintain

operation of the OnStar® system. The OS-311 has on board switching and audio ampliers which allow audio from the

OnStar® system to play through the two front factory speakers when OnStar® is active. This interface retains all warning

chimes, the audible turn signal indicators, and provides a 12v R.A.P. (Retained Accessory Power) output circuit.

Step 1-Pre wire the OS-3RAD wire harness to the aftermarket stereo wire harness.

Step 2-After connecting the OS-3RAD and OS-LAN11 wire harness to the OS-311 main interface, connect the OS-LAN11 connector to the

factory harness.

The Following General Motors Vehicles using the GMLAN 11bit Data Bus with or without a Factory Amplier.

Pontiac: G5 (2007) Solstice (2006-2007)

Saturn:Aura (2007) Sky (2007)

Chevrolet: Cobalt (2007) HHR (2006-2007)

1. The OS-311 does not retain the factory XM receiver. You will lose the XM option when the factory radio is replaced with an aftermarket

radio.

2. If you are not retaining the OnStar® system, use the C2R-GM11 instead of this OS-311 interface.

3. Built in Smart Mute Circuitry will play OnStar® audio through the front speakers while muting the radio or turning the radio off if a mute

input circuit is not present

• OnStar® active LED and Ignition on LED.

• Provides +12v switched accessory output. No more searching for switched +12v in fuse box or kick panel.

• Steering wheel radio controls can be retained to control the new radio by using the SWI - X, JACK, ECL or PS.

• New radio will operate with the vehicle RAP (Retained Accessory Power) circuit. The radio stays on after the key is turned off and stays on

for approximately 10 minutes or until the drivers door is opened.

Note: Connect the Purple/White wire (pin 18) from the OS-3RAD to the radios mute input. If a mute input is not available, connect the

Purple/White wire (pin 18) to the Red/White wire (pin 16) of the OS-3RAD connector.

The Lt. Green wire is a SWC output. Connect this wire to a SWI - X, JACK, ECL, or PS green interface wire. The interface will need to be

programmed for version 1. Do not cut the brown loop. Use the Step by Step programming instructions included with the SWI interface.

Wire locations and Description

WIRECOLORCIRCUITCIRCUITWIRECOLOR

918

817

716

615

514

413

312

211

110

PINNUMBER

N/A

Chime Module

White/Black

Grey/Black

Green/Black

Purple/Black

Black

N/A

Orange

Blue/White

Red

Left Front(-)

Right Front (-)

Left Rear (-)

Right Rear(-)

Ground

Illumination

Amp Turn On

+12v Accessory Output

Left Front (+)

Right Front (+)

Left Rear (+)

Chime Module

Right Rear (+)

+12v Constant

White

Grey

To CM - X

Green

To CM - X

Purple

Yellow

Purple/White

Red/White

Mute Sense

Mute Output

WIRE COLORCIRCUITCIRCUITWIRE COLOR

OrangeIllumination

816

Purple/WhiteGMLAN

715

+12v Constant

Yellow

BlackGround

614

Amplifier Turn On

Blue/White

Purple/BlackRight Rear (-)

513

Right Rear (+)

Purple

Green/BlackLeft Rear (-)

412

Left Rear (+)

Green

OnStar Mono(-)

311

OnStar Mono(+)

Grey/BlackRight Front (-)

210

Right Front (+)

Grey

White/BlackLeft Front (-)

19

Left Front (+)White

PIN NUMBER

White/Purple

White/Brown

Amp Control

Black/White

OS-3RAD

OS-LAN11

Notes

Supported Vehicles

Installation

OS-311

General Motors OnStar®

Interface Installation Instructions

For GMLAN 11bit Vehicles

Produktspezifikationen