Pro1 R251S Bedienungsanleitung


Lies die bedienungsanleitung für Pro1 R251S (2 Seiten) kostenlos online; sie gehört zur Kategorie Thermostat. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 2 Bewertungen. Hast du eine Frage zu Pro1 R251S oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Seite 1/2
R251S
Installation Manual
Pro1 Technologies
P.O. Box 3377
Springeld, MO 65804
Toll Free : 888-776-1427
Web: www.pro1iaq.com
Hours of Operation: M-F 9AM - 6PM Eastern
Table of Contents
Sensor Mounting & Setup
Wiring
Resistance Chart
Specications & Warranty
Page
A trained, experienced
technician must install this
product.
Carefully read these
instructions. You could damage
this product or cause a
hazardous condition if you fail
to follow these instructions.
Una version en espanol de este
manual se puede descargar en
la pagina web de la compania.
Rev. 1809
Wall Mount
Mounting Locations
3-4
5-6
7
8
2
Sensor Mounting & Setup Sensor Mounting & Setup
Connecting to a Wired Sensor Capable Thermostat
The remote sensor should be mounted or placed approximately 4 to
5 feet above the oor. Select an area with average temperature and
good air circulation.
• Close to hot or cold air ducts
That are in direct sunlight
With an outside wall behind the thermostat
• In areas that do not require conditioning
Where there are dead spots or drafts (in
corners or behind doors)
Where appliances could radiate heat.
• Near or on hot appliances.
Remote Sensor Locations
Do not mount or place remote
sensors in these locations:
Do not operate the cooling
system if the outdoor
temperature is below 50˚F
(10˚ C) to prevent possible
compressor damage.
Caution: Equipment
Damage Hazard
The range between the remote sensor and the wired sensing master
thermostat is up to 300 feet. The remote sensor should be installed
using 18 AWG thermostat wire.
Wired Range
Remove the cover of the remote sensor
Mount subbase to the wall
Inside view of
subbase or the
remote sensor
Loosen the terminal block screws. Insert wires, then retighten
terminal block screws.
Non-Flammable
Insulation
Terminal Blocks
Connect the remote sensor to the S terminal blocks on the Wired
Sensor Capable Thermostat.
S1
S2
Place non-ammable insulation into wall opening to prevent
drafts.
Note: Refer to your Wired Sensor Capable
Thermostat manual for setup.
U.S. Registered Trademark. Patents pending
Copyright 2017 All Rights Reserved.
NO
NO
NO
YES
Wiring
Wiring
You can connect 1, 4, 9, or 16 remote sensors to a Wired Sensor Capable
Thermostat to achieve a more accurate temperature average throughout
a space. The following diagrams illustrate the proper ways to wire the
remote sensor. Use 18 AWG thermostat wire when installing.
Wiring
Resistence Chart Technician Setup
1 Remote Sensor
4 Remote Sensors
9 Remote Sensors
16 Remote Sensors
41303113 45.00
115 46.11 39434
117 47.22 37660
119 48.33 35976
121 49.44 34376
123 50.56 32843
125 51.67 31399
127 52.78 30027
129 53.89 28722
131 55.00 27481
133 56.11 26300
135 57.22 25177
137 58.33 24107
139 59.44 23089
141 60.56 22111
143 61.67 21188
145 62.78 20308
147 63.89 19469
149 65.00 18670
151 66.11 17907
153 67.22 17180
155 68.33 16486
157 69.44 15824
159 70.56 15187
161 71.67 14584
163 72.78 14008
165 73.89 13458
167 75.00 12932
169 76.11 12430
171 77.22 11949
173 78.33 11490
175 79.44 11051
177 80.56 10627
179 81.67 10225
181 82.78 9841
183 83.89 9473
185 85.00 9121
187 86.11 8783
-39- 39.44 3916295
-37- 38.33 3627711
-35- 37.22 3362274
-33- 36.11 3117987
-31- 35.00 2893035
-29- 33.89 2685770
-27- 32.78 2494694
-25- 31.67 2318444
-23- 30.56 2155781
-21- 29.44 2004274
-19- 28.33 1865595
-17- 27.22 1737397
-15- 26.11 1618827
-13- 25.00 1509102
-11- 23.89 1407512
-9 -22.78 1313405
-7 -21.67 1226184
-5 -20.56 1145306
-3 -19.44 1069620
-1 -18.33 1000019
1- 17.22 935383
3- 16.11 875329
5- 15.00 819505
7- 13.89 767589
9- 12.78 719284
11 -11.67 674319
13 -10.56 632442
15 -9.44 593086
17 -8.33 556739
19 -7.22 522842
21 -6.11 491217
23 -5.00 461699
25 -3.89 434134
27 -2.78 408383
29 -1.67 384316
31 -0.56 361813
33 0.56 340581
35 1.67 320895
°F C Ohms
°F C Ohms
°F C Ohms
37 2.78 302466
39 3.89 285206
41 5.00 269035
43 6.11 253877
45 7.22 239664
47 8.33 226331
49 9.44 213819
51 10.56 201971
53 11.67 190946
55 12.78 180588
57 13.89 170853
59 15.00 161700
61 16.11 153092
63 17.22 144992
65 18.33 137367
67 19.44 130189
69 20.56 123368
71 21.67 117000
73 22.78 110998
75 23.89 105338
77 25.00 100000
79 26.11 94963
81 27.22 90208
83 28.33 85719
85 29.44 81479
87 30.56 77438
89 31.67 73654
91 32.78 70076
93 33.89 66692
95 35.00 63491
97 36.11 60461
99 37.22 57594
101 38.33 54878
103 39.44 52306
105 40.56 49847
107 41.67 47538
109 42.78 45349
111 43.89 43273
100K Thermistor Output Table
Specications
Operating Temperature ...................... 32˚F to 105˚F (0˚C to +41C)
Operating humidity............................... 90% non-condensing maximum
Dimensions of sensor .......................... 1.5”W x 2.75”H x 0.75”D
Resistance range ...................................Up to 300 feet
Warranty Registration
Your new thermostat has a 5 year limited warranty. You must register
your thermostat within 60 days of installation. Without this
registration the warranty period will begin on date of manufacture.
For warranty issues please contact the HVAC professional that
installed this product. You can register your new thermostat in 2 ways:
Go to the company website, select warranty registration and
ll out a short registration form.
Complete the form below and mail it to the address shown.
Warranty Registration
Online
Mail
S1
S2
S1
S2
S1
S2
S1
S2
Name:
Address:
City:
State:
Zip:
Thermostat Model:
Date Installed:
Complete form and mail to:
Thermostat Warranty Registration
P.O. Box 3377
Springeld, MO 65804


Produktspezifikationen

Marke: Pro1
Kategorie: Thermostat
Modell: R251S

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pro1 R251S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten