Rane AC 22B Bedienungsanleitung
Rane
Nicht kategorisiert
AC 22B
Lies die bedienungsanleitung für Rane AC 22B (13 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Rane AC 22B oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/13
Manual-1
AC 22B
ACTIVE CROSSOVER
OPERATORS MANUAL
AC 22B CONNECTION
In agreement with IEC and AES/ANSI standards, AC 22B
wiring convention is pin 2 Positive, pin 3 Negative (return),
pin 1 Signal ground (for unbalanced use), with the connector
case or shell tied to chassis ground.
BALANCED OPERATION
Use only when driving from a true balanced source and
driving to a true balanced destination—either transformer
coupled or active drive. Connect the input to pins 2 and 3
with pin 2 positive. Do not connect pin 1. Terminate the
shield to the case or shell. Connect the output to pins 2 and 3
with pin 2 positive. Do not connect pin 1. Connect the shield
to the case or shell.
UNBALANCED OPERATION
Connect the input between pins 2 and 1 with pin 2 positive
and pin 1 Signal ground. Short pin 3 to pin 1. Terminate the
shield to the case or shell. Connect the output between pins 2
and 1 with pin 2 Positive. Leave pin 3 open—do not short it
to pin 1. Connect the shield to the case or shell.
COMBINATION OPERATION
For combined balanced and unbalanced operation, use
whichever half of the above instructions apply for each end.
See the “Sound System Interconnection” RaneNote
included with this manual for more information on cabling
and grounding requirements.
QUICK START
The AC 22B can be either a Stereo 2-Way or Mono 3-Way crossover. Labels above the controls refer to the unit being
operated in the 2-Way Stereo mode. Labels below the controls refer to the unit being operated in the 3-Way Mono mode.
The AC 22B is a fully balanced output version of the popular AC 22 and is equipped with XLR conectors instead of
the standard ¼" TRS jacks. All other features, specifications and operation are identical with the standard model with an
added switch. Where the AC 22 is configured somewhat automatically by using switching jacks, the AC 22B is config-
ured by a SYSTEM MODE switch added to the back of the unit.
To operate the AC 22B in Stereo 2-Way mode, be sure that the Mode switch is set for STEREO 2-WAY. Follow the
labels above the controls and jacks.
When operated in the Mono 3-Way mode, the switch should be set in the MONO 3-WAY position. Follow the labels
below the controls and jacks. In Mono 3-Way mode the Channel 1 High Output is unusable. This output is the high-pass-
only portion of the midrange filter. The Channel 1 High Level and the Channel 2 Master Level are also defeated on the
front panel.
NEVER CONNECT ANYTHING EXCEPT AN RS 1 OR OTHER APPROVED RANE AC POWER SUPPLY
TO THE THING THAT LOOKS LIKE A TELEPHONE JACK ON THE REAR. This is an AC supply and requires
some special attention if you do not have an operational power supply EXACTLY like the one that was originally
packed with your unit.
WEAR PARTS: This product contains no wear parts.
Manual-2
FRONT PANEL: STEREO 2-WAY CONFIGURATION
Observe the labels screened above the controls for stereo operation.
POWER switch: Self-evident.
POWER indicator: When this yellow LED is lit the unit is ready to operate.
CHANNEL 1 MASTER LEVEL controls the overall Level of Channel 1 without altering the relative settings of the HIGH
and LOW Outputs. Unity gain for all LEVEL controls is at “7”.
LOW LEVEL controls the Level of signal going to the LOW Output in this Channel. In the MONO SUB mode the Channel
1 LEVEL control sets the Level of the MONO SUB Output, Channel 2's LEVEL control is inactive.
LOW MUTE: When pressed to the in position, all signal is removed from the LOW Output. This eases tune-up procedures,
as described on pages Manual-7 through 13. In the MONO SUB mode, the Channel 1 LOW MUTE switch mutes the
MONO SUB Output, Channel 2's MUTE is inactive.
LOW TIME DELAY control adds from 0 to 2 ms of time Delay to the LOW OUT only. This allows a low frequency driver
to be electronically phase-aligned with a high frequency driver whose diaphragm is situated behind the low frequency
diaphragm. Refer to Time Delay Adjustment on page Manual-6. NOTE: Both DELAY controls are inactive in the MONO
SUB mode.
LOW/HIGH FREQUENCY: This 41-detent selector determines the crossover Frequency between the LOW and HIGH
Outputs. The detents assure maximum accuracy and consistency between Channels. Refer to Selecting Crossover Frequen-
cies on page Manual-6 to determine the proper setting for your particular system.
HIGH LEVEL controls the Level of signal going to the HIGH Output in this Channel.
CHANNEL 2 MASTER LEVEL controls the overall Level of Channel 2 without altering relative settings of the HIGH and
LOW Outputs.
Produktspezifikationen
| Marke: | Rane |
| Kategorie: | Nicht kategorisiert |
| Modell: | AC 22B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Rane AC 22B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Rane
7 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- Friedland
- CyberPower
- Seecode
- OnePlus
- Moultrie
- Jura
- B-Speech
- ChamSys
- IPEGA
- Source Audio
- RAB
- Sun Pumps
- Thermador
- Indesit
- Seiki
Neueste Bedienungsanleitung für -Kategorien-
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025