Rane SEQ 30L Bedienungsanleitung
Rane
Nicht kategorisiert
SEQ 30L
Lies die bedienungsanleitung für Rane SEQ 30L (5 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Rane SEQ 30L oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/5
Manual-1
QUICK START
If this is your first equalizer, please do yourself and
your speakers a favor and read at least the first five
pages. “An ounce of prevention...,” and all that.
The SEQ 30L is a stereo equalizer, so adjusting
any slider affects both channels simultaneously. Begin
by setting all sliders to their center detent (0 dB), and
the INPUT LEVEL to its center detent (0 dB). Try to
make more cuts than boosts. After equalizing, use the
EQ switch to compare equalized and non-equalized
signal. While EQ is switched to ACTIVE (out), adjust
the INPUT LEVEL to the same level as when EQ is
switched to BYPASS (in).
You may use either the XLR or ¼" connectors for
Inputs or Outputs. Connect only one INPUT type per
channel. The XLR and ¼" TRS inputs do not sum.
You may, however, use both types of OUTPUTS
simultaneously if desired.
WEAR PARTS: This product contains no wear parts.
OPERATORS MANUAL
SEQ 30L
STEREO GRAPHIC EQUALIZER
Manual-2
EQ BYPASS switch
When pressed to BYPASS, the filter sliders have no effect. Since actual unity
gain depends on varying slider settings, use the BYPASS switch to determine the
unity gain position of the INPUT LEVEL control by comparing ACTIVE and
BYPASS volumes.
Filter level slide controls
Each of these sliders control the
output level of both channels of the 30
bandpass filters. Center position is
grounded for guaranteed flat response.
Cable Wiring
In agreement with IEC and AES/ANSI standards, XLR wiring convention is pin
2 Positive (hot), pin 3 Negative (cold), and pin 1 Signal ground (for unbalanced
use). Pin 1 and the connector case or shell are tied to chassis ground.
INPUT LEVEL control and indicators
This controls the overall level. 0 dB gain is reached at the center detent with all
sliders centered at their 0 dB detents. Set the INPUT LEVEL to give equal volumes
with the EQ switched to ACTIVE or BYPASS, after setting the sliders (see EQ
BYPASS switch below). Apply sufficient signal to the input to occasionally light
the +4 dBu indicator. Flashing of the OL (overload) LED during peaks can be
avoided by turning the INPUT LEVEL or boosted Filters down.
Manual-3
POWER switch and LED
Your basic, straightforward power
switch. When the yellow LED is lit, the
SEQ 30L is ready to go.
LEFT & RIGHT OUTPUTS
Use either the Balanced XLR or the
Unbalanced ¼" TS jacks. Using both
types of Outputs are permissible to
drive two devices, such as an amplifier
and a recorder.
LEFT & RIGHT INPUTS
Choose between the balanced XLR
or the balanced/unbalanced ¼" TRS
jacks, but only use one. Inserting a ¼"
TS jack will work—however—always
use balanced lines especially when
connecting cables over 10 feet in length.
Consult SOUND SYSTEM INTER-
CONNECTION on page Manual-6.
Produktspezifikationen
| Marke: | Rane |
| Kategorie: | Nicht kategorisiert |
| Modell: | SEQ 30L |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Rane SEQ 30L benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Rane
7 Juli 2025
7 Juli 2025
7 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- TESLA Electronics
- Ritter
- Rocketfish
- USAopoly
- ChamSys
- Vivanco
- Besco
- EWON
- Eschenbach
- Wolff Finnhaus
- Visage
- Avantco
- JUNG
- IDance
- Approx
Neueste Bedienungsanleitung für -Kategorien-
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025