Rane SSE 22 Bedienungsanleitung
Rane
Nicht kategorisiert
SSE 22
Lies die bedienungsanleitung für Rane SSE 22 (6 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Rane SSE 22 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/6

Manual-1
SSE 22
HOME CINEMA EQUALIZER
OPERATORS MANUAL
THX is a registered trademark of Lucasfilm Ltd.
Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation
QUICK START
Great video is easy; great audio is hard, but a SSE 22 makes it a lot easier. Read at least this boxed section and you’ll be
on your way toward great audio.
Hook-up is intuitive: In from the controller, out to the amplifiers. Just follow the silkscreened legends near the gold-
plated RCA jacks on the rear of the unit.
Familiarity with other graphic and parametric equalizers makes the SSE 22 just as familiar. If this is your first equalizer,
be gentle; it can overwhelm you.
Use the switch as an aid in comparing equalized results with unequalized results. Pushbutton BYPASS in and locked
(LED on) is the bypassed (unequalized) mode; pushbutton (LED out off) is the normal equalized mode. See the Operating
Instructions on the page Manual-4 for alignment information.
Install the supplied security cover after completing all settings. Be sure the light fits snugly into the hole in thePOWER
security cover.
Never connect anything except an approved Rane power supply to the thing that looks like a red telephone jack on
the rear of the unit. This is an AC input and requires special attention if you do not have a power supply exactly like the
one originally packed with your unit. See the full explanation of the power supply requirements on page Manual-3.

Manual-2
FRONT PANEL DESCRIPTION
1. Graphic equalizer filter level controls. The Left and Right Channels have eleven slide controls used to set the individual
levels of the constant-Q filters. Their range is ±6 dB. The grounded center-detent design ensures each filter is off when
positioned to 0 dB.
2. Parametric equalizer LEVEL control. Two parametric sections are included in each Channel with a ±6 dB range. This
control sets the amount of boost/cut for each parametric section. Same grounded center-detent design as the Graphic
Equalizer sections.
3. Parametric equalizer BANDWIDTH control. Slide control used to set the Bandwidth for this filter section. The range is
0.7-3.5 octaves.
4. Parametric equalizer FREQUENCY control. Slide control used to determine the center Frequency for this filter section.
The range is 1 kHz-10 kHz.
5. POWER indicator. This LED lights any time power is supplied from the Rane model RS 1 power supply (included). To
avoid confusion a distinction is made here between electrical and political.
6. Overall BYPASS switch & indicator. This pushbutton switch activates the “hard-wire” BYPASS function. When engaged
(red BYPASS LED on), the INPUT connectors directly tie to the OUTPUT connectors (hard-wired). Engaging this switch
converts the SSE 22 into a relatively expensive patch cord, albeit one with pretty lights. During the initial timed power-up
sequence or power loss of any sort, the SSE 22 is automatically in BYPASS mode.

Manual-3
REAR PANEL DESCRIPTION
1. Remote POWER supply input. The unit is supplied from the factory with a Model RS 1 Remote Power Supply suitable for
connection to this input jack. The power requirements of the unit call for an 18 volt AC center-tapped transformer only. This
is not a telephone jack. Never use a power supply other than the one supplied, or a replacement approved by Rane Corpo-
ration. Using any other type of supply may damage the unit and void the warranty.
2. Chassis ground. A #6-32 screw is used for chassis grounding purposes. See the CHASSIS GROUNDING note below.
3. RCA OUTPUT connectors. Active unbalanced design. Use only high-grade RCA cables for interconnect to the power
amplifier inputs. For balanced amplifier inputs, use a Rane BB 44X Balance Buddy, or consult the RaneNote “Sound System
Interconnection” available from the factory or downloadable from the Rane web site.
4. RCA INPUT connectors. Active unbalanced design. Use only high-grade RCA cables for interconnect to the controller
outputs.
CHASSIS GROUNDING
If after hooking up your system it exhibits excessive hum or buzzing, there is an incompatibility in the grounding
configuration between units somewhere. Your mission, should you accept it, is to discover how your particular system
wants to be grounded. Here are some things to try:
1. Try combinations of lifting grounds on units that are supplied with ground lift switches or links.
2. If your equipment is in a rack, verify that all chassis are tied to a good earth ground, either through the line cord
grounding pin or the rack screws to another grounded chassis.
3. Units with outboard power supplies do NOT ground the chassis through the line cord. Make sure that these units are
grounded either to another chassis which is earth grounded, or directly to the grounding screw on an AC outlet cover by
means of a wire connected to a screw on the chassis with a star washer to guarantee proper contact.
Produktspezifikationen
Marke: | Rane |
Kategorie: | Nicht kategorisiert |
Modell: | SSE 22 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Rane SSE 22 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Rane
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- Khind
- Kettler
- Crimson
- Intel
- Linq
- Rooboost
- Foscam
- Kärcher
- Compex
- Airlux
- Daewoo
- Ruger
- Lehle
- Banana Pi
- MaximaVida
Neueste Bedienungsanleitung für -Kategorien-
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025
6 Juli 2025