StarTech.com POEINJ1G90W Bedienungsanleitung

Lies die bedienungsanleitung für StarTech.com POEINJ1G90W (2 Seiten) kostenlos online; sie gehört zur Kategorie Måleinstrumenter. Dieses Handbuch wurde von 29 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 4 Bewertungen. Hast du eine Frage zu StarTech.com POEINJ1G90W oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: June 2, 2020 11:37 AM

Product Diagram (POEINJ1G90W)

Component Function

1Power LEDs• A is detected.Green:Power Source

• A is not detected.O:Power Source

2PoE LED

• Indicates that the is Amber:PoE Injector

providing power.

• Indicates that the is in idle O:PoE Injector

mode.

3PoE Out Port• Connect a (PD) to the Powered Device PoE

Injector.

4Data Port• Connect a to the Network SwitchPoE

Injector.

54-Pin Terminal Block

V1 and V2

• Connect an external (48-56V DC Power Source

DC Input) to the .PoE Injector

6Ground Screw

• Connect a ground connection to the Ground

ScrewDC Power Source when connecting a to

the .PoE Injector

Requirements

For the latest requirements, please visit www.startech.com/POEINJ1G90W

• Small Flat Head Screwdriver x 1

• (Optional) Phillips® Head Screwdriver x 1

• (Optional) Writing Utensil x 1

• PoE Powered Device (PD) x 1

• Network Switch x 1

• DC Power Source or Universal Power Adapter with Type N (OD: 5.5 mm, ID: 2.5 mm)

Barrel Connector x 1

90W Industrial Grade Hardened 802.3bt PoE Injector | 1G (1000 Mbps)

• RJ45 Terminated UTP/STP Cat 5e (or better) Network Cable x 2

Powering the PoE Injector

Terminal Block

Connecting and installing the , must be completed by a 4-Wire Terminal Connector

licensed Electrician.

Notes: Make sure that you turn o the power source before connecting the power wire

to the .PoE Injector

Do not exceed the recommend power source voltage as it may result in personal or

product damage.

1. Using a , loosen the two screws (V1 or V2) on the Small Flat Head Screwdriver

4-Wire Terminal Connector (included).

2. Connect the from a (48 - 56V DC), or the provided Power WiresDC Power Source

Barrel Power Connector Adapter, Terminal Block Connectorsto the proper to

the terminals are marked on the . Connect the positive wire to PoE Injector’s Casing

V+ and the negative wire to V-.

3. Tighten the two screws on the .4-Wire Terminal Connector

4. Insert the in the on the 4-Wire Terminal Connector4-Wire Terminal BlockPoE

Injector.

5. To connect a second to the , repeat steps 1 - 4.Power SourcePoE Injector

6. Using a , loosen the on the .Phillips Head ScrewdriverGround ScrewPoE Injector

7. Connect the from a to the on the Ground WireDC Power SourceGround Screw

PoE Injector.

8. Using the , tighten the to secure thePhillips Head ScrewdriverGround Screw

Grounding Wire PoE Injectorto the.

(Optional) Barrel Connector

• Connect a from a Type N (OD: 5.5 mm, ID: 2.5 mm) Barrel ConnectorUniversal

Power AdapterTerminal Block to Barrel Power Connector Adapter. to the

Connecting the PoE Injector

Notes: Make sure the total length of the connecting the CAT5e/6 CablePD Device

to the and the connecting the to the PoE InjectorCAT5e/6 CablePoE Injector

Remote Switch does not exceed 100 meters in total length.

The is compatible with both Power over Ethernet (PoE) and 95W Power PoE Injector

over HDBaseT (PoH).

12 345 6

Produktspezifikationen