Vigitron VI27000 Bedienungsanleitung
Vigitron
Nicht kategorisiert
VI27000
Lies die bedienungsanleitung für Vigitron VI27000 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 36 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 18.5 Bewertungen. Hast du eine Frage zu Vigitron VI27000 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Application Drawing
Vi27000/Vi27001 Single-Pair Ethernet & PoE Transmission Solution Install ion at Manual
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING O QUALIFIED T
SERVICE PERSONNEL.
IP Camera-end Installation
The Smart Choice for Transmission Solutions www.vigitron.com
Important Safety Warning
- Install the Vi27000 “Remote Unit” near the Camera end.
- Connect the IP camera RJ45 connect
or to the 10/100BaseT Ethernet ort of
Vi27000 using a standard Cat5/6 cable of maximum 100 m .
- Connect one end of the long Single Pair Wire to the 2-pin Terminal block of
Vi27000. Make sure the Single Pair Wire polarity matches on the Vi27001 End.
The link LED on the 10/100 connector should be “ON” to indicate proper connection
between the camera and Vi27000.
The PoE LED on the 10/100 connector should be "ON" when PoE is used to power
up the camera. The Status LED on the Single Pair Wire side should be “ON” and
flashing to indicate proper connection.
Ethernet Switch-end Installation
- Install the Vi27001 “Local Unit” near the network switch.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT Ethernet
port of Vi27001 using a standard Cat5/6 cable of maximum 100 m.
- Connect one end of the long Single Pair Wire to the to the 2-pin Terminal block of
Vi27001. Make sure the Single Pair Wire polarity matches on the Vi27000 End.
The link LED on the 10/100 Ethernet connector should be “ON” to indicate proper
connection between the switch and Vi27001. Also the Status LED on the Single Pair
Wire side should be “ON” and flashing to indicate proper connection.
-If the Vi27001 receives power using PoE, make certain the power adaptor is not
connected. The Vi27000 and camera will receive power from the PSE source.
-If a PSE source such as a PoE network switch is not available, external power
must be provided to the Vi27001.
CAUTION:
If an external power supply adaptor is plugged into Vi27000 or Vi27001, the unit will
not use or pass thru PoE power from the PoE switch. It will use the power from the
plugged in DC power supply.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should conform
to all local codes.
- DO NOT bundle low-voltage signals in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products to rain,
moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.
- DO NOT install the unit in a place where the operating ambient temperature
exceeds 65° C.
- Make sure that the external power supply output voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
-
Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power supply cord or plug is
damaged, liquid has been spilled, or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
- The mains plug is used as the disconnect device and shall remain readily operable.
Ethe et Extendersrn
TM
T C r™ Vhe Omnii oppe i27000 ie er s is r ry ra evolutiona data t ansmission
solution that extends full-duplex High peed -S Ether PoE net and over
ingl aie r ir re inf ast uctu es. r r The V ri27000 is a t ansmitter that ope ates inr
conjunction ith w 1- ort V ri27001 o 4- ort i2700V 4 r r receive s ove vi tually any
2 conductor wir res eliably. The Vi2700X r ’s unique t ansmission technology
eliminates the potential for r c oss talk r r t esulting in the pe fec solution for
bundled cable runs d tor use in many eleva and building
communication systems.
U W wer p to 36 po can be provided from a souPoE rce or wer a poDC supply at
t Vhe i27001 (Rx) to the control e tsid elimina ing rthe need fo a local power
supply at the c a location. amer The i27000 ie opeV er s rat extendede at
t r rempe atu e ange r - . 30°C to +65°C
I r r rnstallation cost savings, tested and p oven design and pe fo man ce go into
making the fect solution foVi27000 eries the per r building CCTV wir .ing
WARNING! - To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture. This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as vases shall be placed on the
apparatus.
WARNING! - This apparatus is a Class I product. This product must be
connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and shall
remain readily operable.
The Vi27001 receiver can use a local power supply to power Vi27000 transmitter and the IP camera using PoE.
Data + PoE
Data
Single Pair
Cat5/6
Data + PoE
Cat5/6
Network Switch
PoE Camera
Vi27000
Vi27001
Vi1120
Both use o s v o o t Vhe i27001 and t V he i27000 can local power s tupplies power them el es and provide P E t the camera IP .
Data
Data
Single Pair
Cat5/6
Data + PoE
Cat5/6
Network Switch
PoE Camera
Vi27000
Vi27001
Vi0017
Vi1120/Vi001
PoE Switch
T a a o h.he Vi27000 series and IP camera can be powered by P E switc
PoE Camera
Vi27000Vi27001
Data + PoE
Data + PoE
Single Pair
Cat5/6
Data + PoE
Cat5/6
Produktspezifikationen
| Marke: | Vigitron |
| Kategorie: | Nicht kategorisiert |
| Modell: | VI27000 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Vigitron VI27000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Vigitron
18 September 2025
18 September 2025
18 September 2025
18 September 2025
19 Juni 2025
19 Juni 2025
18 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Wilbur Curtis
- Emeril Lagasse
- SatKing
- Goodway
- Belkin
- Indiana Line
- UPO
- Lümme
- Shimbol
- Senco
- Westcott
- Sun Pumps
- Bluebird
- ETON
- Crane
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026