Vigitron VI27001 Bedienungsanleitung

Lies die bedienungsanleitung für Vigitron VI27001 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 47 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 24 Bewertungen. Hast du eine Frage zu Vigitron VI27001 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Application Drawing

Vi27000/Vi27001 Single-Pair Ethernet & PoE Transmission Solution Installion atManual

DO NOT OPEN

RISK OF ELECTRIC SHOCK

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER. NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICINGO QUALIFIED T

SERVICE PERSONNEL.

IP Camera-end Installation

The Smart Choice for Transmission Solutionswww.vigitron.com

Important Safety Warning

-Install the Vi27000 “Remote Unit” near the Camera end.

-Connect the IP camera RJ45 connect

or to the 10/100BaseT Ethernet ort of

Vi27000 using a standard Cat5/6 cable of maximum 100 m .

-Connect one end of the long Single Pair Wire to the 2-pin Terminal block of

Vi27000. Make sure the Single Pair Wire polarity matches on the Vi27001 End.

The link LED on the 10/100 connector should be “ON” to indicate proper connection

between the camera and Vi27000.

The PoE LED on the 10/100 connector should be "ON" when PoE is used to power

up the camera. The Status LED on the Single Pair Wire side should be “ON” and

flashing to indicate proper connection.

Ethernet Switch-end Installation

-Install the Vi27001 “Local Unit” near the network switch.

-Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT Ethernet

port of Vi27001 using a standard Cat5/6 cable of maximum 100 m.

-Connect one end of the long Single Pair Wire to the to the 2-pin Terminal block of

Vi27001. Make sure the Single Pair Wire polarity matches on the Vi27000 End.

The link LED on the 10/100 Ethernet connector should be “ON” to indicate proper

connection between the switch and Vi27001. Also the Status LED on the Single Pair

Wire side should be “ON” and flashing to indicate proper connection.

-If the Vi27001 receives power using PoE, make certain the power adaptor is not

connected. The Vi27000 and camera will receive power from the PSE source.

-If a PSE source such as a PoE network switch is not available, external power

must be provided to the Vi27001.

CAUTION:

If an external power supply adaptor is plugged into Vi27000 or Vi27001, the unit will

not use or pass thru PoE power from the PoE switch. It will use the power from the

plugged in DC power supply.

-Read these instructions.

-Keep these instructions.

-Heed all warnings.

-Follow all instructions.

-Do not use this apparatus near water.

-Clean only with a dry cloth.

-Install in accordance with the manufacturer’s instructions.

-This installation should be made by a qualified service person and should conform

to all local codes.

-DO NOT bundle low-voltage signals in the same conduit as high-voltage wiring.

-To reduce the risk of fire or electrical shock, do not expose these products to rain,

moisture, dripping or splashing.

-No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.

-DO NOT install the unit in a place where the operating ambient temperature

exceeds 65° C.

- Make sure that the external power supply output voltage is in the recommended range.

-Do not install near any heat sources such as radiators, heat registers, stoves or

other apparatus (including DVRs) that produce heat.

-Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

-Only use attachments/accessories specified by the manufacturer.

-

Unplug this apparatus during lightning storms or when unused for long periods of time.

-Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as a power supply cord or plug is

damaged, liquid has been spilled, or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

-The mains plug is used as the disconnect device and shall remain readily operable.

Etheet Extendersrn

TM

TCr™ Vhe Omniioppei27000ie ers is rry ra evolutionadata tansmission

solution that extends full-duplex Highpeed -SEtherPoE net and over

inglaier irre infastuctues. rrThe Vri27000 is a tansmitter that opeates inr

conjunction ith w1-ort Vri27001 o 4-ort i2700V4 rrreceives ove vitually any

2 conductor wirres eliably. The Vi2700Xr ’s unique tansmission technology

eliminates the potential forr coss talk rrt esulting in the pefecsolution for

bundled cable runsd tor usein many eleva and building

communication systems.

UWwer p to 36 pocan be provided from a souPoErce orwer a poDC supply at

tVhe i27001 (Rx) to the control etsid eliminaing rthe need fo a local power

supply at the ca location. amerThe i27000ieopeV ers ratextendede at

trrempeatue ange r-. 30°C to +65°C

Irrrnstallation cost savings, tested and poven design and pefoman ce go into

making the fect solution foVi27000 eries the perr building CCTV wir.ing

WARNING! - To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture. This apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as vases shall be placed on the

apparatus.

WARNING! - This apparatus is a Class I product. This product must be

connected to a mains socket outlet thru an AC to DC Power supply.

WARNING! - The mains plug is used as the disconnect device and shall

remain readily operable.

The Vi27001 receiver can use a local power supply to power Vi27000 transmitter and the IP camera using PoE.

Data + PoE

Data

Single Pair

Cat5/6

Data + PoE

Cat5/6

Network Switch

PoE Camera

Vi27000

Vi27001

Vi1120

Both use o sv oo t Vhei27001and t V hei27000canlocalpower s tuppliespower themelesandprovide PE t thecamera IP .

Data

Data

Single Pair

Cat5/6

Data + PoE

Cat5/6

Network Switch

PoE Camera

Vi27000

Vi27001

Vi0017

Vi1120/Vi001

PoE Switch

T a aoh.he Vi27000series and IP camera canbepoweredby PE switc

PoE Camera

Vi27000Vi27001

Data + PoE

Data + PoE

Single Pair

Cat5/6

Data + PoE

Cat5/6

Produktspezifikationen