Atoll IN400 Bedienungsanleitung

Atoll Empfänger IN400

Lies die bedienungsanleitung für Atoll IN400 (4 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Atoll IN400 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/4

ATOLL ELECTRONIQUE

OWNER’S MANUAL ~ INTEGRATED IN400 EVO

ATOLL ELECTRONIQUEPage 5

CONNECTINGS REMOTE CONTROL

Warning: reduce the volume of the source connected to BY-PASS before

any use of the BY-PASS Input.

14) ON / SLEEP button (preheating) by

pressing; source selection (rotation).

15) Headphones jack: speakers outputs

are switched off when headphones are

plugged in.

16) STANDBY LED.

DETAIL OF FUNCTIONS

14 15 16 17 18

8) USB input (type B).

9 10)& Optical inputs 1 & 2.

11 12)& Coaxial inputs 1 & 2.

13) Bluetooth sensor.

Digital input card (optional):

Trigger cable must be a Male to Male stereo jack plug

Ø 3,5 mm (1/8”).

Jack

3,5 mm

1) Auxiliary input (optional phono), CD

input, Tuner, DVD, Tape (PLAY), Tape

output (REC), BY-PASS input, Preamp.

outputs (to 1 or 2 power amplifiers or to

a Subwoofer).

2) 2×XLR input – right channel.

3) 12V Trigger output: this output allows the

switching off/on of any device equipped with

a compatible Trigger input (see instructions).

4) 2×XLR input – left channel

5) ON/OFF switch and general plug-in

(with protection fuse).

6) Right speaker output (

& ).

7) Left speaker output (

& ).

17) Display: shows the selected source (on the

left) and volume level (on the right).

18) Power ON knob, volume and menus setup.

Access to Balance (1 press) and Light

(2 press). See “Remote control” chapter.

Optional

digital board

4 5

78 9 10 11 12 13

Page 4

The remote control is supplied with 2 CR2032 Lithium batteries. In addition to your IN400

Integrated, it also allows you to control all ATOLL products: CD players, Tuner, Integrated

or preamps with the remote control option. (See the user manual for these models).

19) VOL: Volume adjustment button

(from 0 to 80).

20) SEL: Input selection button

21) MUTE: When the device is in Mute, no function is

available except STANDBY. To exit, press any active key

on the remote control.

22) DISP: Display power off and on button (pressing any

button turns the display back on for 3 seconds).

23) ON / SLEEP.

24) Direct access to sources.

25) BY-PASS (*).

26) NUM: Selection of COAX 1 & 2 and OPT 1 & 2

digital inputs.

27) CONFIG: Access to menus:

– Balance (1 press): once in the balance menu, adjustment is made using the

VOL

& keys. The volume is distributed from -9 to +9 on each channel.

– Light (2 presses): in this menu, you can choose with the keys VOL

& the color of the

backlighting of the buttons on the front panel between Red, Green, Orange or off.

– Display (3 presses): with the keys VOL

& select OFF to turn off the display.

– SBY ECO (4 presses): with the keys VOL

& select the time after which the device will

switch to economy mode when in STANDBY.

- OFF: the device remains in preheating mode: consumption will be 32 W.

- 10 sec, 5 min, 15 min, 30 min, 60 min: Consumption < 0,5 W after the set time.

– A long press on CONFIG allows you to rename the selected entry. Choose the characters

with the keys VOL

& and move to the next character with the SEL keys

& and validate

by pressing CONFIG again.

The BY-PASS input allows you to use your IN400 as a power block (to be connected to

the output of an audio-video preamp for example). This input is selected via the front

panel (25), the SEL

/ buttons on the remote control or the BY-PASS button. Once

this input is selected, the word “BY-PASS” is displayed on the screen and only the

SEL

/ and standby functions remain accessible. To exit the BY-PASS, press the BY-

PASS button on the remote control or change source.

(*) USING OF THE BY-PASS INPUT

Touches

non

fonction-

nelles

ATOLL ELECTRONIQUE

OWNER’S MANUAL ~ INTEGRATED IN400 EVO

ATOLL ELECTRONIQUEPage 3Page 6

CAUTIONS

• Do not make any connections when your device is turned on.

• Always switch off your appliance before moving it or before

any changes of wires on the rear.

• Install your appliance in a dry, well-ventilated place away from

any source of heat.

• Make sure you never put anything on your amplifier.

• Avoid any short circuits.

• Carefully observe the polarity & and, as well as the left and

right connection directions.

• Never connect two speakers in parallel to the same output.

ADVISES

• Your amplifier will provide you with optimal listening quality

approximately half an hour after switching it on, the time

it takes for the power stages to reach their ideal operating

temperature. Between two uses, it is therefore preferable to

use the rest position so that the power stages remain at their

optimal temperature. At night or when you leave your home, it

is preferable to use the main switch to turn off the device.

• We advise you to choose good quality connection cables (to

other devices as well as to speakers). Do not hesitate to seek

advice from your specialist dealer.

BLUETOOTH®

Your appliance allows the reception of audio signals sent since any device having a

Bluetooth® transmitter (Smartphone, tab, computer…).

First time association:

• Activate Bluetooth connectivity on your sending device.

is displayed.

• Select it from the list of devices (named IN300).

• Once the connection is made, the symbol

appears.

All the audio signals that will be played on your source device will then be

transmitted to your device. The device remains paired until the IN300 is turned off

or the connection is terminated. It will remain visible to your transmitter.

Association of another emitter:

• Once associated with any transmitter, it is essential to completely turn off

your device at the ON/SLEEP (preheating) switch to be able to make it

visible to another transmitter.

For better reception quality, avoid being more than 5 meters from your device.

Your device is equipped with an asynchronous USB (type B) input (11). You will only

be able to use it after installing the correct driver on your computer. This driver can

be downloaded freely from our website:

• Accepted format on Optical and Coaxial inputs: 16-24 bits (44,1 kHz,

48 kHz, 88,2 kHz, 96 kHz, 176,4 kHz and 192 kHz).

• Accepted format on USB input:

– DSD: DSD64, DSD128 & DSD256.

– PCM: 16-32 bits (44,1 kHz, 48 kHz, 88,2 kHz, 96 kHz, 176,4 kHz,

192 kHz, 352,8 kHz, 384 kHz).

You will find attached an explanatory note on its installation.

This driver is not required for Macintosh computers.

In order to avoid problems with high quality format transfers

(24 bits / 192kHz), it is recommended to use a USB connection

cable with ferrite.

USB INPUT

ACCEPTED FORMATS

https://www.atoll-electronique.com/en/xmos-specific-driver-usb/

ATOLL ELECTRONIQUE

OWNER’S MANUAL ~ INTEGRATED IN400 EVO

ATOLL ELECTRONIQUEPage 7Page 2

You have just bought an integrated amp-preamp. IN400 with EVO

exceptional audiophile performances. We really thank you for your

confidence in our products. To get the best part of your amplifier, please read

carefully this manual.

ATOLL ELECTRONIQUE®

is a French Company that designs, manufactures,

and commercializes all its products.

Areas with a gray background only concern functions that can be used with an

integrated unit that has the digital input board.

ABOUT THIS MANUAL

Power in Wrms/channel/8Ω (230v):

Power in Wrms/channel/4Ω (230v):

Supply:

Total of capacitors:

Number of inputs:

Switch OFF consumption:

Power consumption in standby (ECO):

Power consumption in preheating mode:

Power consumption in operation:

Input impedance:

Maximum input level:

Sensitivity:

Signal-to-noise ratio:

Distortion rate at 1 kHz:

Bandwidth (-3 dB):

Rise time:

Dimensions:

Weight:

2×160 W

2×300 W

1050 VA

96 680 µF

– 2×XLR inputs.

– 5 LINE inputs: AUX and

PHONO (option).

– 1 BY-PASS input.

0 W

<0,5 W

32 W

34 W - 800 W

357 kΩ

3,5 Vrms

450 mV

100 dB

0,05%

5 Hz - 100 kHz

2 µs

440×370×130 mm

19,5 Kg

TECHNICAL DATA

(technical data are subject to changes)

YOU WILL FIND ENCLOSED

– An integrated amplifier-preamplifier IN400 EVO.

– A power cord.

– An ATOLL global remote control supplied with 2 CR2032 Lithium batteries.

– This user manual accompanied by a warranty certificate.

Latest update: 25th September 2024

Produktspezifikationen

Marke:	Atoll
Kategorie:	Empfänger
Modell:	IN400
Breite:	440 mm
Tiefe:	330 mm
Gewicht:	20000 g
Produktfarbe:	Silber
Übertragungstechnik:	Kabelgebunden
Höhe:	130 mm
Audio Kanäle:	- Kanäle
THD, totalklirren:	0.05 %
Rauschverhältnis (SNR):	100 dB
RMS Leistungsoutput pro Kanal (4 Ohm):	300 W
Eingang Empfindlichkeit:	100 mV
Synchronisations-Eingangsimpedanz:	220000 Ohm
Leistungshöhepunkt pro Kanal:	300 W
RMS Leistungsoutput pro Kanal (8 Ohm):	160 W