EXSYS EX-1332V Bedienungsanleitung

EXSYS Nicht kategorisiert EX-1332V

Lies die bedienungsanleitung für EXSYS EX-1332V (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 9 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 5 Bewertungen. Hast du eine Frage zu EXSYS EX-1332V oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/2

Because the designs of computers are dierent, only general installation instructions are

given. Please refer your computer’s reference manual whenever in doubt.

1. Connect the USB cable to the USB B Connector of the module.

2. Plug the power supply into the 5V Connector (optional).

3. Now connect the other end from the USB cable ( A-Plug) to the A-Connector at

your PC.

HARDWARE INSTALLATION :

6 5

EXEXEX

-1332V / 1334V1332V / 1334V1332V / 1334V

EnglishEnglishEnglish

EXEXEX

-1332V / 1334V1332V / 1334V1332V / 1334V

EnglishEnglishEnglish

Die USB zu Seriell Module sind zur Umsetzung von USB auf bis zu 4 RS-232 Schnitt-

stellen mit FIFO 16C550 Ports für den Anschluss von High Speed Seriellen RS-232

Peripherie Geräten (z.B. Modem, Plotter usw.) geeignet. Die Module sind Hot Plug &

Play fähig. Für die Einstellungen der I/O Adressen und Interrupts sind keine Jumper und

Einstellungen notwendig. Sie werden vom System und beim Installieren des Betriebs-

systems automatisch vorgenommen.

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

Kompatibilität: USB 1.1 & 2.0 Anschluss

Betriebssysteme: WIN 9.x/ ME/ 2000/ XP/ Server 200x/ Vista/ 7/ 8, Linux, MAC

Anschlüsse: 9 Pin RS-232 Sub-D Stecker, 1 x USB B-Buchse, 1 x 5V Buchse

Lieferumfang: 1 x USB zu Seriell Modul, Anleitung, CD, USB Kabel

Zertikate:

CECE

/ FCC / RoHS / WEEE DE97424562

DRIVER INSTALLATION :

JUMPER EINSTELLUNG & ANSCHLÜSSE :

ACHTUNG !!! Nur mit optionalem Original Netzteil verwenden !!!

5 Volt

Buchse:

CLEANING :

For cleaning please use only a dry u less cloth and remove the dirt with gently pres-

sure. In the area of the connectors please make sure that no bres from the cloth re-

main in the connectors. Attention! Never use a moist or wet cloth for cleaning!

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Seriell 9 Pin D-SUB Stecker:

DB 9M:

USB B Buchse:

USB 2.0 B-Buchse:

Pin Signal Pin Signal

1 VCC 3 DATA+

2 DATA- 4 GND

Achtung!

Stecker nie umge-

kehrt oder mit

Gewalt einstecken.

DRIVER INSTALLATION :

BedienungsanleitungBedienungsanleitung

Vers. 1.3 / 06.06.13

S2 9 Pin Stecker

Seriell RS232

S1 9 Pin Stecker

Seriell RS232

EX-1332V

1 x USB B-Anschluss

verschraubbar

EX-1334V

S1- 4 x 9 Pin Stecker

S4 Seriell RS232

1 x USB B-Anschluss

verschraubbar

Windows XP/ Vista/ 2000/ Server 200x/ 7/ 8 (32&64-Bit) :

Windows will recognize a new “FT232R USB UART“ and open the hardware assistant.

Please choose manual installation and put the driver CD into your CD-Rom drive. Enter

the Path

"D:\USB_to_IO\FTDI\(32_64bit)Win7_8_XP_Vista_2008_2008R2_2003_2000”.

into the box for the Path/Source and click at . Now Windows search for >next/continue<

the drivers in the specied directory. Follow the hardware assistant and nish the instal-

lation. If Windows recognizes other new devices repeat the above described steps.

Attention! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at <> < then enter and click at . In the windows Start Run “compmgmt.msc“ >OK<

that open select Under you should nd >Device Manager<. ”Ports (COM and LPT)“

one more new as sample (COM5). If you see this or similar entries "USB Serial Port„

the module is installed correctly.

INSTALL THE PERIPHERAL DEVICE:

The speed from the serial ports can be set to the maximum baud rate of 115.2Kbaud.

With double click select for example < >Device manager< > USB Serial Port (COM5) .

Now you can select the dierent settings of baud rate, stop/start-bits etc. This setting

you can use also for the other COM ports.

Windows 98/ 98SE/ ME:

Windows will recognize a new “FT232R USB UART“ and open the hardware assistant.

Please choose manual installation and put the driver CD into your CD-Rom drive (as

sample D:) . Now enter the Path “D:\USB_to_IO\FTDI\Win98_ME” into the box for the

Path/Source and click at . Now Windows search for the drivers in the >next/continue<

specied directory. Follow the hardware assistant and nish the installation. If Windows

recognizes other new devices repeat the above described steps. Restart Attention!

Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at <> < then enter and click at . In the windows Start Run “compmgmt.msc“ >OK<

that open select Under you should nd >Device Manager<. ”Ports (COM and LPT)“

one more new as sample (COM3). If you see this or similar entries "USB Serial Port„

the module is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM 5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 to 256.

LINUX:

There are drivers available for Linux. The drivers are located in the folder

“D:\USB_to_IO\FTDI\Linux x86_64“ on the driver CD. They are supported by the most

versions of Linux. Because each individual distribution and kernel version of Linux is

dierent, sadly we cant provide a installation instruction. Please refer to the installation

manual for standard IO ports from your Linux version !

MAC:

There are drivers available for MAC. The drivers are located in the folder

“D:\USB_to_IO\FTDI\MAC OSX or Mac_OS_9_8“ on the driver CD. They are support-

ed by the most versions of MAC OS. Because each individual version of MAC OS is

dierent, sadly we cant provide a installation instruction. Please refer to the installation

manual for standard IO ports from your MAC OS version !

Produktspezifikationen

Marke:	EXSYS
Kategorie:	Nicht kategorisiert
Modell:	EX-1332V
Breite:	150 mm
Tiefe:	70 mm
Gewicht:	360 g
Mitgelieferte Kabel:	USB
Produktfarbe:	Grau
Übertragungstechnik:	Kabelgebunden
Höhe:	30 mm
Betriebstemperatur:	0 - 55 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Zertifizierung:	CE, FC, ROHS
Kabellänge:	2 m
Plug & Play:	Ja
Mac-Kompatibilität:	Ja
Kompatible Betriebssysteme:	Win 98SE, ME, 2000, Server 2003, XP, Vista\nLinux\nMac OS
Unterstützte Protokolle:	TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Anzahl serielle Anschlüsse:	2
Hostschnittstelle:	PCI
Weitere Anschlüsse:	1x B-female\n2x 9-pin D-SUB serial male
Datenübertragungsrate:	0.1 Mbit/s
Anzahl Anschlüsse:	2
Chipsatz:	FTDI