Festo PAML-CP-186-HP3-G2 Bedienungsanleitung

Lies die bedienungsanleitung für Festo PAML-CP-186-HP3-G2 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 21 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 11 Bewertungen. Hast du eine Frage zu Festo PAML-CP-186-HP3-G2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

PAML-CP/-MK-186

Sub-base/Module connector

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Assembly instructions

8161951

2021-10b

[8161953]

Translation of the original instructions

© 2021 all rights reserved to Festo SE & Co. KG

1

Applicable documents

All available documents for the product

è

www.festo.com/sp.

2Safety

2.1Safety instructions

–

Only use the product in its original condition without unauthorised modifica-

tions.

–

Only use the product if it is in perfect technical condition.

–

Take the weight of an individual device or a service unit into account.

Dependent on the design, a mounted service unit can weigh more than 100 kg.

–

Under intended use the surface temperature may reach 60 °C. Allow the device

to cool down before working on it.

–Make sure the mounting surface is sufficiently strong for the maximum forces.

–

Only use suitable mounting components.

–Mount the individual device or the service unit only on flat surfaces.

2.2Intended use

–The sub-base PAML-CP serves as an adapter for the pneumatic connection and

for pipe mounting for in-line installation of service units.

–The module connector PAML-MK is used to connect two service units of the

same size.

2.3Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can eval-

uate the work and detect dangers. Personnel must have the relevant mechanical

training.

3Additional Information

–

Accessories

è

www.festo.com/catalogue.

4Product Range Overview

4.1Scope of delivery

1

2

3

4

5

Fig. 1:

Sub-base PAML-CP

1

Front plate (1x)

2

Rear plate (1x)

3

Screw (8x)

4

Washer (8x)

5

O-ring (2x)

6

7

8

9

Fig. 2:

Module connector PAML-MK

6

Screw (2x)

7

Front plate (1x)

8

O-ring (1x)

9

Rear plate (1x)

4.2

Not in scope of delivery

10

11

Fig.3

10

Electrical pressure regulator (1x)

PREL-186

11

Micro filter (1x)

PFML-186

5

Assembly

5.1Mounting the connecting plates PAML-CP

1

2

3

4

5

12

Fig.4

1.Orient the front plate and the rear plate so the stamp number on the12

sub-base corresponds with the stamp number on the housing (1 to 1 and 2 to

2) and the mounting thread for wall mounting points to the rear.aB

2.Insert the O-rings in the slots provided.5

3.

Position the front plate and the rear plate .12

4.Fasten the front plate and the rear plate to the service unit using four12

screws and four washers . Tightening torque: 27 Nm ± 15% 34

5.Comply with the maximum screw-in depth for the pipe connection.

ISO 228Max. screw-in depth [mm]

G1/212

G1 1/420

G1 1/222

G224

G2 1/226

Produktspezifikationen