Hartell LTP-1 Bedienungsanleitung

Lies die bedienungsanleitung für Hartell LTP-1 (2 Seiten) kostenlos online; sie gehört zur Kategorie Wasserpumpe. Dieses Handbuch wurde von 17 Personen als hilfreich bewertet und erhielt im Schnitt 3.8 Sterne aus 9 Bewertungen. Hast du eine Frage zu Hartell LTP-1 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Literature # 900917 2019

100 East Graham Place

Burbank, CA 91502

Web: www.hartell.com

Email: info@hartell.com

INSTALLATION • OPERATION • MAINTENANCE

NTRODUCTION

HARTELL LTS and LTP are generalpurpose reservoir pumps developed for laundry and wet bar -

applications. These models are utilized to pump wastewater from an area with no floor drains to

an overhead or remote drain line. The pump must be installed in conjunction with a (laundry) tub/

sink. This pump has been carefully engineered to provide long, trouble free service and is of the

highest quality workmanship and materials.

These pumps have been thoroughly inspected and tested, then carefully packaged to insure safe

delivery and operation. When you receive your pump, examine it carefully to determine that there

are no damaged or broken parts. If damage is detected, notify the firm from where the pump was

purchased. They will assist with a repair or replacement.

See the precautions listed below before continuing.

CAUTION: READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

- Pump should only be used with liquids compatible with pump component materials. Do not use

to pump flammable or explosive fluids. Do not use in explosive atmospheres.

- The pump is supplied with a grounding type plug. To reduce the risk of electrical shock be

certain that it is connected to a properly grounded, grounding receptacle.

- Do not handle pump with wet hands or when standing on a wet or damp surface, or in water.

- Shut off the electrical power at the fuse box before making any connections. All wiring must

comply with local codes.

- A strainer must be installed in the tub to prevent foreign objects, (buttons, screws, etc.), from

entering and damaging the pump. In laundry applications a lint trap must be installed to prevent

an excessive build-up of lint that could interfere with proper float/switch and impeller operation.

A nylon stocking works well as a lint trap.

- Applying heat directly to the tank with a torch, or indirectly by heat transfer through copper

tubing can melt the tank. This will void the warranty. Solder fittings and tubing first, allow to cool,

and then assemble to the tank. The use of some pipe dopes will soften and/or crack the plastic

used in this pump. This will void the warranty. Use only Teflon tape when installing threaded

fittings to the tank.

ONE YEAR LIMITED WARRANTY

HARTELL LTP and LTS waste water pumps are guaranteed to be free from defects in

workmanship or materials and to function satisfactorily, when properly installed, for a period of

ONE (1) year from date of installation. HARTELL will replace, without charge, any HARTELL

product found to be defective upon examination at our factory if returned within the guarantee

period, transportation charges prepaid.

This guarantee does not apply if the product has been misapplied or mechanically damaged,

HARTELL assumes no liability for resultant damages of any kind arising out of the use of its

products.

Keep these sheets with the pump. They may be valuable if service is needed under

the terms of the warranty.

Model #: _______________________ Date of installation: ______________

Installer: ________________________ Date Code: ____________________

Dealer: _________________________

MODEL LTP1 801284 & LTS1 801285--

WASTE WATER REMOVAL PUMP

ItemQtyPart #Descripon

11

630092- Motor LTS1, 115 VAC, 1/3 hp

630090- Motor LTP1, 115 VAC, 1/4 hp

21SJE Switch Float Assembly w/Gasket (2000 to present) 620172 L-211S

31Impeller Sha Seal 640087 P-107

41

630057 PS103- Impeller with Set Screw, LTS

650030 PA103- Impeller with Set Screw, LTP

51

640089 PS106- Impeller Sha with Sleeve

640069 PA106- Impeller Sha with Sleeve

61Gasket Set (Perimeter Seal, Switch & Impeller Seals) 620155 P115

71Tank Cover 640095 P-100

81Tank 640096 P-112

91Impeller Chamber Cover 200500 P-104

Produktspezifikationen