Heatit Multireg IceControl Pro Bedienungsanleitung
Heatit
Nicht kategorisiert
Multireg IceControl Pro
Lies die bedienungsanleitung für Heatit Multireg IceControl Pro (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 9 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 5 Bewertungen. Hast du eine Frage zu Heatit Multireg IceControl Pro oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
2. ABOUT AUTOMATIC SNOW MELTING
With automatic snow melting, you keep it dry and ice-free throughout
the winter. This contributes to both increased safety against falls and
accidents when it is slippery, as well as saving work with shoveling,
spreading and salting. Ground sensors can be installed in places where
snow and ice problems normally occur, which gives you functional
and energy-saving control of the heating cables. The sensors can be
installed in concrete or asphalt, or placed under paving stones and
tiles, in addition to the roof/gutter. There are also precipitation sensors
for wall mounting where you cannot place the sensor in the ground.
Whether it is ice or snow on stairs, in the entrance or driveway that is
the problem, a thermostat can be used to regulate the system. The
thermostat receives information about temperature and humidity from
a sensor, and it knows itself if there is rain or snow, and the risk of ice
formation. Based on system settings and your wishes, it will ensure ice-
free access to, for example, the mailbox or garage.
A pre-programmed installation procedure guides you through the
setup, helping you make the choices that suit your needs. Based on
your choices, the snow melt thermostat suggests the optimal settings
for your conguration.
3. INSTALLATION GUIDELINES
The power supply must always be disconnected before installation or
maintenance work on the control unit or on components connected
to it. This control unit or components connected to it must only be
installed by a registered installation company. The product must be
installed and documented in accordance with the current edition of
NEK 400 and the installation instructions.
How to install Multireg IceControl Pro
1. Use a at object (e.g. a at-head screwdriver) to bend the trigger on
the DIN rail.
2. Place the top of the Multireg IceControl Pro mounting slot over the
top of the DIN rail.
3. Bend the Multireg IceControl Pro towards the DIN rail until the
bottom clicks into place.
Make all necessary connections to the device, and reconnect the
power once all connections are made.
PREPARATION AND CONNECTION OF CABLES
Before connecting, the cables must be stripped of approx. 6mm.
Be careful not to damage the conductors. Tighten the cables with a
torque of 0.5 Nm. The cable size should be between 12 and 30 AWG.
MULTIREG
ICECONTROL PRO
Firmware 1.10
01.01.2020
Installation guide
Version 2025-F (01.11.25)
CONTENT
1. Introduction
2. About snow melting automation
3. Installation guidelines
4. Connection
4.1 Overview of connection Multireg IceControl Pro
4.2 Connection diagram IceControl ground sensor TF GS
4.3 Connection diagram IceControl air sensor TF AIS
4.4 Placement of IceControl ground sensor TF GS
5. First-time startup/restart
6. Menu
7. Advanced settings
7.1 Ground sensor 1
7.2 IceControl air sensor TF AIS
7.3 IceControl gutter sensor TF TS2
7.4 IceControl rain and snow sensor
7.5 Other advanced settings items
7.6 System information
8. Connecting other sensors
8.1 Connection diagram IceControl gutter sensor TF TS2
8.2 Connection diagram IceControl rain and snow sensor
- Location of IceControl rain and snow sensor
Product information
Accessories for automatic snow melting
MODBUS 485
1. INTRODUCTION
Multireg IceControl Pro is a control unit for up to two heating zones.
It is designed to melt snow and ice on the ground, in stairs and on
roofs and in gutters. You can control the heating in the ground and the
heating cables in the gutter with one and the same system. If you are
going to have two zones with ground heating, you must also have two
ground sensors.
Multireg IceControl Pro is compatible with several types of ground
and air sensors. The controller is used for electric heating systems. It is
equipped with a simple and user-friendly menu. Read the installation
instructions carefully before starting up.
Produktspezifikationen
| Marke: | Heatit |
| Kategorie: | Nicht kategorisiert |
| Modell: | Multireg IceControl Pro |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Heatit Multireg IceControl Pro benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Heatit
12 Januar 2026
28 Dezember 2025
5 September 2024
5 September 2024
27 August 2024
27 August 2024
30 April 2024
11 Februar 2024
10 Januar 2024
22 September 2023
Bedienungsanleitung Nicht kategorisiert
- Cube Controls
- HuddleCamHD
- UltraLink
- Oreck
- AV:link
- CAME-TV
- Clean Paper
- Javalo Elf
- VICSEED
- Primo
- ComNet
- Interlogix
- MINOX
- Tovsto
- Salewa
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026