Heatit Z-WATER2 Bedienungsanleitung

Lies die bedienungsanleitung für Heatit Z-WATER2 (5 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 65 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 33 Bewertungen. Hast du eine Frage zu Heatit Z-WATER2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

1. INTRODUCTION

Heatit Z-Water2 is a DIN-rail regulator for controlling

waterbased heating systems. The module clips right onto a

DIN-rail and allows you to control your waterbased heating

through your Z-Wave™ network.

Heatit Z-Water2 is equipped with 9 potential free relays for

actuators. It also has 2 analog inputs for temperature sensors.

The Heatit Z-Water2 relays may be controlled by associations

with other Z-Wave thermostats e.g Heatit. Each relay can

control one or several actuators in your underfloor heating

system.

2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE

MANUFACTURERS

Please read this before installation

This device may be used with all devices certified with the

Z-Wave Plus™ certificate and should be compatible with

such devices produced by any manufacturer. Every primary

controller is dierent depending on the manufacturer, their

target audience and intended use/application. Please review

the functionalities implemented by the primary controller you

intend to use with our Z-Wave Plus certified device to ensure

that it provides the necessary controls to take full advantage of

our product’s capabilities.

3. BEHAVIOR WITHIN THE Z-WAVE NETWORK

This device may be operated within any Z-Wave™ network

with Z-Wave-certified devices from other manufacturers. All

non-battery-operated nodes within the network will act as

repeaters regardless of manufacturer to increase the reliability

of the network. On delivery, the device does not belong to any

Z-Wave network. The device needs to be added to an existing

network to communicate with the other devices within it.

Devices may also be removed from a network. The add/

remove processes are initiated by the primary controller of the

Z-Wave network.

4. INSTALLATION GUIDELINES

Installation must be done by a qualified electrician in

accordance with national building codes. Before installation,

disconnect the power to the device from the mains. During

installation of the device, power to the device must be

disconnected AT ALL TIMES!

Max tightening torque for terminal screws: 2Nm

Use the following procedure to install Heatit Z-Water2:

1. Place the top part of the DIN rail mounting on the Heatit

Z-Water2 over the top of the DIN rail so it hooks onto the

rail.

2. Use a flathead screwdriver to push the DIN rail mounting tab

downward.

3. Tilt the bottom of the Heatit Z-Water2 until it touches the

DIN rail. Now let go of the DIN rail mounting tab so it locks

into place.

4. Make all the necessary connections to the device (max

tightening torque for all screw terminals is 2Nm). Apply

power to the device after all connections have been made.

TABLE OF CONTENTS

1. Introduction

2. Statement regarding products from multiple

manufacturers

3. Behaviour within the Z-Wave network

4. Installation guidelines

5. Connections

6. Quick Start

7. Add/Remove

7.1 Method 1: Standard (Manual)

7.2 Method 2: SmartStart (Automatic)

8. Factory Reset

9. Startup

10. LED blinking patterns description

11.QR-Code Placement (DSK)

12. Security

13. Node Information Frame

14. Associations

14.1Setting and Removing Associations

15. Association Groups

16. Configuration Parameters

17.Calibration

18.Command Classes

18.1Basic Command CLass

18.2Binary Switch Command Class

18.3. Multilevel Sensor Command Class

18.4. Indicator Command Class

19.Supported Command Classes

20. Other features

21. Dimensions

22. External antenna connector

Product info

HEATIT

Z-WATER2

Installers manual

Firmware versionDocument version

FW 1.02023-A

Article no.Document date

45 124 9501.05.2023

Org. doc. date 01.05.2023

TO PRODUCT

DOCUMENTS

Produktspezifikationen