Honeywell C7189R Bedienungsanleitung
Honeywell
Thermostat
C7189R
Lies die bedienungsanleitung für Honeywell C7189R (20 Seiten) kostenlos online; sie gehört zur Kategorie Thermostat. Dieses Handbuch wurde von 19 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 10 Bewertungen. Hast du eine Frage zu Honeywell C7189R oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/20
Installation
Guide
C7189R
Wireless Indoor Sensor
Capteur d’intérieur sans fil
Sensor inalámbrico para interiores
69-2459EFS-05
Installation Guide
ii
69-2459EFS—05
® U.S. Registered Trademark.
Copyright © 2012 Honeywell International Inc.
All rights reserved.
About your wireless indoor sensor
This sensor monitors temperature and humidity in any indoor location and transmits it
wirelessly to the thermostat.
You can set the system to monitor temperature at the thermostat, or at the sensor location,
or use an average of both to optimize comfort throughout the home. The thermostat can
use up to 6 wireless indoor sensors.
When multiple sensors are installed, the thermostat can monitor temperature and humidity
in separate locations. For example, one sensor can control humidication on the main level,
while another controls dehumidication in a crawl space. For more information, see the
instructions provided with the thermostat.
Note: The wireless indoor sensor is compatible only with RedLINK 2.0 thermostats.
Operating Ambient Temperature: 0 to 120° F (-17.8 to 48.9° C)
For Optimal Battery Life: 35 to 114° F (1.7 to 45.6° C)
Operating Relative Humidity: 5% to 90% (non-condensing)
Physical Dimensions: 2-7/8 x 1-7/8 x 15/16 inches (74 x 48 x 24 mm)
The thermostat will display a warning to replace batteries in the indoor sensor about 2 months
before power is depleted. The sensor status light will begin flashing red about 2–3 weeks before
power is depleted. During normal operation, the status light remains off.
Wireless Indoor Sensor
169-2459EFS—05
MCR32933
MCR32934 MCR32935
Install 2 fresh AAA alkaline batteries.
Status light will briefly flash green. If it
flashes red, batteries are not good.
Install batteries and link sensor to thermostat
1
Install batteries, then enter Wireless Setup mode at the thermostat. Press and
release the CONNECT button to link the wireless sensor to the thermostat.
Press and release CONNECT.
After a short delay, the status light
will glow green for 15 seconds.
If the status light is red, the
sensor did not link with the
thermostat. See Note.
Verify the thermostat is in the Wireless Setup
mode and the indoor sensor is at least 2 feet
away from the EIM or thermostat.
Produktspezifikationen
| Marke: | Honeywell |
| Kategorie: | Thermostat |
| Modell: | C7189R |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Honeywell C7189R benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Thermostat Honeywell
5 Oktober 2024
4 Oktober 2024
30 September 2024
27 September 2024
24 September 2024
15 September 2024
13 September 2024
13 September 2024
12 September 2024
8 September 2024
Bedienungsanleitung Thermostat
- Plugwise
- Magnum
- PECO
- Heatmiser
- HomePilot
- Hama
- MundoControl
- De Dietrich
- Levica
- Homematic IP
- Eqiva
- Stiebel Eltron
- BTicino
- Mikoterm
- Wattio
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
14 Juni 2025
14 Juni 2025
12 Juni 2025
12 Juni 2025
12 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025